Grizzly G0820 Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 104

Grizzly G0820 Скачать руководство пользователя страница 77

Model G0820 (Mfd. Since 12/16)

-75-

Blade Tilt Calibration

The blade tilt stops are calibrated at the factory,
but they can be recalibrated if they change during
the life of the machine. The 0° stop positions the
blade square to the table.

Tools Needed

Qty

Hex Wrench 3mm .............................................. 1
Open-End Wrench 8mm.................................... 1
Machinist's Squares, 90° & 45° ...................1 Ea.

0° Stop

1. DISCONNECT MACHINE FROM POWER!

2. Move blade tilt to 0° and raise main blade as

high as it will go.

3. Open cabinet door and identify stop nuts

shown in

Figure 153.

4. Use machinist's square to check if main blade

is square to table (see

Figure 154).

Figure 155. Tilt scale cable hex nuts.

a. If main blade is not square to table, loos-

en the two set screws on 0° stop nut, then
loosen stop nut away from leadscrew
collar.

b. Adjust main blade tilt angle so that it is

square to table.

c. Thread 0° stop nut against leadscrew col-

lar and retighten set screws.

45° Stop

Use a similar procedure for the 45° stop nut
shown in

Figure 153, as previously instructed for

the 0° stop nut.

Tilt Scale Calibration

If necessary, the blade tilt scale on the front of the
saw can be adjusted by using the hex nuts shown
on the tilt scale cable in

Figure 155. These are

accessed inside the cabinet.

Table

90° Square

Blade

Figure 154. Machinist's square against blade

and table.

Figure 153. Blade tilt stop nuts.

Leadscrew

Collar

Tilt Scale

Cable Hex Nuts

0° Stop

Nut

45° Stop

Nut

«
...
75
76
77
78
79
...
»

Содержание G0820









































































































Отзывы:

Нет отзывов