Grizzly G0820 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 104

Grizzly G0820 Скачать руководство пользователя страница 38

-36-

Model G0820 (Mfd. Since 12/16)

Figure 62. Up-close view of power supply

terminal inside junction box.

R and T

Connections

Ground

Power

Connection

Junction Box

Do not swap "R" or "T" wires with ground

wire inside power connection junction

box. Doing so will electrify machine frame,

which could cause electrocution. Make sure

incoming ground wire is only connected to

left-most terminal post in the power con-

nection junction box so machine is properly

grounded.

7. Press Emergency Stop button on front of

machine to turn machine

OFF.

8. WITHOUT resetting Emergency Stop button,

press ON button. Machine should not start.

— If machine does start (with Emergency

Stop  button  pushed  in),  immediately  dis-
connect  power  to  machine.  Emergency
Stop  button  safety  feature  is  not  working
correctly.  This  safety  feature  must  work
properly  before  proceeding  with  regular
operations. Call Tech Support for help.

9. Reset Emergency Stop button on front of

machine.

11. Move sliding table all the way right, then open

blade cover, as shown in

Figure 64. This

activates blade cover safety switch to prevent
saw from starting while cover is open.

Figure 64. Blade cover open.

Blade Cover

12. While staying safely away from blade, reset

Emergency Stop button, then try to start main
blade and scoring blade.

— If blades do not start, blade cover safety

switch safety feature is working correctly.

— If blades do start (with blade cover open),

immediately turn machine

OFF and dis-

connect power. The blade cover safety
switch safety feature is not working cor-
rectly. This safety feature must work prop-
erly before proceeding with regular opera-
tions. Call Tech Support for help.

13. Carefully close blade cover, then move slid-

ing table back to center of machine.

10. Repeat Steps 7–9 with Emergency Stop but-

ton on rear of cabinet (see

Figure 63).

Figure 63. Emergency Stop on cabinet.

Emergency Stop

Button

«
...
36
37
38
39
40
...
»

Содержание G0820









































































































Отзывы:

Нет отзывов