Grizzly G0820 Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 104

Grizzly G0820 Скачать руководство пользователя страница 71

Model G0820 (Mfd. Since 12/16)

-69-

Lubrication

An  essential  part  of  lubrication  is  cleaning  the
components  before  lubricating  them.  This  step
is  critical  because  dust  and  chips  build  up  on
lubricated  components,  which  makes  them  hard
to move. Simply adding more lubrication to built-
up  grime  will  not  result  in  smooth-moving  parts.
Clean the components in this section with an oil/
grease  solvent  cleaner  or  mineral  spirits  before
applying lubrication.

All bearings are sealed and permanently lubri-
cated. Leave them alone until they need to be
replaced.

Trunnions

Lubrication Type ... T26419 or NLGI#2 Equivalent
Amount ..................................................1-2 Dabs
Lubrication Frequency .....................6–12 Months

To grease the blade-height trunnion, move the
blade all the way down and smear a dab of grease
into the trunnion groove shown in

Figure 145,

then move the blade through its full range of
movement to spread the grease.

To grease the blade-tilt trunnions, move the slid-
ing table out of the way, open the blade guard,
then tilt the blade to 0°. From the front of the saw,
smear a dab of grease in the front of the trunnion
grooves on both sides. Now, tilt the blade to 45°
and reach inside the cabinet and smear a dab of
grease into the back of the trunnion grooves on
both sides. Tilt the blade through its full range of
movement to spread the grease.

To reduce risk of shock or

accidental startup, always

disconnect machine from

power before adjustments,

maintenance, or service.

Items Needed

Qty

NLGI#2 Grease or Equivalent ........... As Needed
Grease Gun ....................................................... 1
Mineral Spirits .................................... As Needed
Clean Shop Rags .............................. As Needed
Light Machine Oil............................... As Needed

Figure 145. Trunnion lubrication locations (table

removed for clarity).

Blade Height Trunnion

(Grease Behind Plate)

Blade Tilt

Trunnions

«
...
69
70
71
72
73
...
»

Содержание G0820









































































































Отзывы:

Нет отзывов