Grizzly G0820 Скачать руководство пользователя страница 30

Страница: 30 / 104

-28-

Model G0820 (Mfd. Since 12/16)

26. While still holding T-handle wrench, thread

arbor nut on counterclockwise and fully tight-
en it to secure blade (see

Figure 34).

Before proceeding with the next steps, wear

gloves to protect your hands when handling

and installing blade.

25. Slide main blade (not included) over arbor

with teeth facing to the right, then install
flange (see

Figure 33).

Figure 33. Main blade component assembly.

Arbor

Flange

Arbor

Nut

Upper Teeth
Facing Right

28. Install riving knife or splitter/riving knife, as

shown in

Figure 40, but do not tighten

mounting bolt yet (refer to

Riving Knife

Alignment beginning on Page 43 for detailed
information).

Figure 35. Installing splitter/riving knife.

Splitter/Riving

Knife

27. Close blade cover, then move sliding table all

the way back and remove T-handle wrench.

Figure 34. Main blade installed on arbor.

Main Blade

Arbor Nut

Flange

. Adjust riving knife or splitter/riving knife

approximately

⁄

" away from main blade,

using a

⁄

" or 3mm hex wrench as a guide

(see

Figure 36).

Figure 36. Adjusting splitter/riving knife-to-blade

spacing.

Hex Wrench

Mounting Bolt

Содержание G0820









































































































Результаты поиска

Содержание G0820

Отзывы:

Grizzly G0820, Руководство пользователя, Страница: 30 / 104

Результаты поиска

Содержание G0820

Отзывы: