Grizzly G0820 Скачать руководство пользователя страница 55

Страница: 55 / 104

Model G0820 (Mfd. Since 12/16)

-53-

4. Place

fence

vertical

position

(see

Figure 107) for thicker workpieces, or

in horizontal position for thinner workpieces
and for angled cuts where blade is tilted over
fence.

3. Loosen slide lock lever shown in Figure 106.

Figure 106. Location of slide lock lever.

Slide Lock

Lever

Vertical

Horizontal

Figure 107. Rip fence positions.

5. Position leading edge of rip fence so it

extends across extension wing, as shown in

Figure 108, then retighten lock lever.

6. Lift rip fence lock lever (see Figure 108) and

adjust fence to approximate width of cut.

7. Tighten micro-adjust lock knob (see

Figure 108), then turn micro-adjust knob to
fine tune width of cut.

Figure 108. Proper position of rip fence.

Rip Fence

Lock Lever

Micro-Adjust

Lock Knob

Micro-Adjust

Knob

8. Push rip fence lock lever down to secure

fence assembly in position.

9. Load workpiece onto table saw. The setup

should look similar to

Figure 101 on Page 51.

10. Take all necessary safety precautions, then

perform cutting operation.

Содержание G0820









































































































Результаты поиска

Содержание G0820

Отзывы:

Grizzly G0820, Руководство пользователя, Страница: 55 / 104

Результаты поиска

Содержание G0820

Отзывы: