Grizzly G0820 Скачать руководство пользователя страница 49

Страница: 49 / 104

Model G0820 (Mfd. Since 12/16)

-47-

5. Slide arbor wrench behind scoring blade onto

flats of arbor (see

Figure 87) to prevent blade

from spinning.

Figure 87. Inserting arbor wrench behind scoring

blade to prevent blade from spinning.

Arbor

Wrench

6. Unthread arbor hex bolt counterclockwise

(left-hand threads), and remove arbor hex
bolt, flange, and blade (

see Figure 88).

Figure 88. Scoring blade, flange, arbor hex bolt,

19mm wrench, and arbor wrench.

Hex Bolt

7. Install scoring blade set, flange, and arbor

hex bolt in reverse order from removal, mak-
ing sure upper blade teeth face LEFT (see

Figure 89), then tighten arbor hex bolt.

8. Align scoring blade with main blade, as

instructed in next subsection.

Arbor

Flange

Upper Teeth
Facing Left

Hex Bolt

Figure 89. Scoring blade order of assembly.

Arbor

Wrench

Flange

19mm Wrench

Scoring

Blade

Содержание G0820









































































































Результаты поиска

Содержание G0820

Отзывы:

Grizzly G0820, Руководство пользователя, Страница: 49 / 104

Результаты поиска

Содержание G0820

Отзывы: