Grizzly EXTREME G0513X2 Скачать руководство пользователя | Manualshive

Страница: 35 / 100

background image

G0513 Series Bandsaws (Mfd. Since 08/22)

-33-

The  deflection  method  is  much  more  subjective
than  the  flutter  method.  Each  blade  will  deflect
differently  and  every  user  will  determine  what
"moderate  pressure"  means.  The  following  are
general  guidelines  for  tensioning  the  blade  with
this method.

To tension bandsaw blade using deflection

method:

1. DISCONNECT MACHINE FROM POWER!

2. Make sure the blade is properly tracking as

instructed in the

Initial Blade Tracking on

Page 27.

3. Raise guide post all the way and move upper

and lower guide bearings away from blade
(refer to

Page 35 for more information).

4. Engage blade tension quick-release lever to

apply tension to blade.

5. Using moderate pressure, push center of

blade sideways.

— If blade deflects approximately

1

⁄

4

", it is

properly tensioned. Proceed to

Step 6.

— If blade deflects less than

1

⁄

4

", it is over-ten-

sioned. Rotate blade tension handwheel
counterclockwise two full turns and repeat

Step 5.

— If blade deflects

1

⁄

4

" or more, blade is not

properly tensioned. Rotate blade tension
handwheel clockwise to incrementally ten-
sion blade, and repeat

Step 5 until blade

is properly tensioned.

6. Adjust blade guides as described in Adjusting

Blade Support Bearings and Adjusting

Blade Guide on Pages 34–35.

The Deflection Method

Fine Tune Tracking

During setup, the blade was tracked without the
machine connected to power (refer to

Page 27).

In this procedure, the bandsaw is turned

ON to

perform fine tuning of the tracking. Make small
changes with the blade tracking knob as you
monitor the effect on the blade tracking.

To fine tune blade tracking:

1. Close wheel covers and turn bandsaw ON.

2. Observe blade tracking path through clear

tracking window on right edge of bandsaw
(see

Figures 44–45).

Figure 44. Example of blade, viewed through

tracking window.

3. If necessary, loosen tracking control lock

lever and use tracking control knob (see
Figure 45) to adjust the blade so it tracks on
the center of the wheel.

4. Tighten tracking control lock lever (see Figure

45) to secure setting, then turn machine OFF.

Figure 45. Fine-tune tracking controls.

Blade

Tracking

Window

Tracking

Control

Lock

Lever

Tracking

Control

Knob

«
...
33
34
35
36
37
...
»

Содержание EXTREME G0513X2





































































































Отзывы:

Нет отзывов

Похожие инструкции для EXTREME G0513X2

Бренд: Scheppach Страницы: 256

Бренд: Parkside Страницы: 65

SICI-7-1/4A3 11004

Бренд: Truper Страницы: 24

Бренд: Rockwell Страницы: 8

Бренд: MDL POWERUP Страницы: 16

Бренд: Baileigh Industrial Страницы: 56

Бренд: Parkside Страницы: 92

Бренд: Hafco Woodmaster Страницы: 32

Бренд: Black & Decker Страницы: 34

Fire Storm 609746-08

Бренд: Black & Decker Страницы: 7

Бренд: Black & Decker Страницы: 7

FireStorm FS18SS

Бренд: Black & Decker Страницы: 40

Бренд: Black & Decker Страницы: 7

Бренд: Black & Decker Страницы: 84

Бренд: Black & Decker Страницы: 96

Бренд: Black & Decker Страницы: 96

Бренд: Black & Decker Страницы: 4

Бренд: Palmgren Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды