manualshive.com logo in svg

Grizzly EXTREME G0513X2, Руководство пользователя

Поделиться
Скачать
Grizzly EXTREME G0513X2 Скачать руководство пользователя страница 37

G0513 Series Bandsaws (Mfd. Since 08/22)

-35-

To adjust the upper blade guides:

1.  DISCONNECT MACHINE FROM POWER!

2.  Loosen the thumb screws shown in Figure 48.

Before adjusting the blade guides, make 

sure the blade is tracking properly (Page 27) 

and that it is correctly tensioned (Page 32).

Adjusting Blade 

Guides

The  blade  guides  provide  side-to-side  support 
to  keep  the  blade  straight  while  cutting.  These 
guides are adjustable in two ways—forward-and-
back and side-to-side.

To keep the blade straight while cutting, the blade 
guides must be as close to the sides of the blade 
without exerting any clamping pressure. This dis-
tance is typically about 0.004".

To prevent damage to the blade teeth as the blade 
deflects  back  while  cutting,  the  guides  must  be 
behind the teeth gullets the same amount as the 
support bearing is behind the blade, which is typi-
cally about 0.016" (see 

Figure 47 on the previous 

page for an illustration of this relationship).

Note:  Models G0513 and G0513A40 use car-
bide discs as guides; models G0513X2 and 
G0513X2BF use ball bearings.

IMPORTANT: Although the function and the dis-
tance adjustment of the blade guides is the same 
for  all  the  G0513  Series  Models,  the  guide  con-
trols are not all the same. Use the set of instruc-
tions on the following pages that is correct for your 
model of bandsaw.

Blade
Guide

Tooth

Gullet

Blade

0.016"

Gap

Support

Bearing

Blade

0.016"

Gap

0.016"

Gap

Support

Bearing

Blade

Guides

0.004"

Gap

Blade

Figure 49. Correct gap between guide guides 

and blade.

3.  By  hand,  adjust  the  distance  of  the  guides 

approximately  0.004"  from  the  sides  of  the 
blade  (see 

Figure  49),  then  re-tighten  the 

thumb screws to secure the setting.

Figure 48. Upper blade guide components 

(guide post cover removed for clarity).

Thumb Screws

Blade Guides

Models G0513 & G0513A40

Tools Needed 

Qty

Hex Wrench 5mm .............................................. 1
Feeler Gauges 0.004", 0.016" ...................1 Each 
Fine Ruler .......................................................... 1

Содержание EXTREME G0513X2





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды