Grizzly EXTREME G0513X2 Скачать руководство пользователя страница 57

Страница: 57 / 100

G0513 Series Bandsaws (Mfd. Since 08/22)

-55-

Using Drift Bar

1. Secure drift bar on resaw fence with adjustable

handle. Make sure drift bar is flat against
fence face and is straight up and down.

2. Slide resaw fence over moving plate on fence

assembly and tighten lock handle.

3. Move resaw fence up to blade so center of

drift bar is set approximately

⁄

" forward of

blade teeth (see

Figure 84).

Figure 84. Resaw fence with drift bar installed.

1/4"

Blade

Resaw Fence

Drift

Bar

Drift Bar

Blade

4. Mark reference cut line along top of workpiece

(see

Figure 85).

5. Lower bandsaw blade guides as close to

workpiece as possible (see

Figure 85).

6. Adjust resaw fence so blade aligns with mark

made in

Step 4 and center of drift bar is set

⁄

" forward of blade teeth (see

Figure 85).

7. Lock rip fence and resaw fence in position.

8. If necessary for cutting operation, support

ends of board with saw stand or roller stand.

9. Turn bandsaw ON.

10. Slowly feed workpiece completely through

blade. Use drift bar as a pivot point to control
cut, as shown in

Figure 86.

Note: The drift bar allows you to steer your
workpiece while cutting to quickly correct
blade lead and keep blade aligned with cut
line.

Figure 86. Resawing with drift bar.

Blade

Drift

Bar

Workpiece

Cut Line

Mark

Blade

Guides

Figure 85. Workpiece positioned to cut using

resaw fence with drift bar.

Workpiece

Cut Line

Mark

Blade

Guides

Drift

Bar

1/4"

Blade

Resaw Fence

Drift

Bar

Blade

Model G0513A40 includes a drift bar that installs
on the resaw fence and is designed to help reduce
blade lead by creating a pivot point that provides
more control during resaw operations.

To use drift bar:

Содержание EXTREME G0513X2





































































































Результаты поиска

Содержание EXTREME G0513X2

Отзывы:

Бренды по названию

Популярные бренды

Grizzly EXTREME G0513X2, Руководство пользователя

Результаты поиска

Содержание EXTREME G0513X2

Отзывы:

Бренды по названию

Популярные бренды