Grizzly EXTREME G0513X2 Скачать руководство пользователя страница 53

Страница: 53 / 100

G0513 Series Bandsaws (Mfd. Since 08/22)

-51-

Changing Blade

Figure 75. Placing blade on the wheels.

4. Tighten the blade tension lever.

5. Adjust the blade tension (refer to Page 32)

and blade tracking (refer to

Page 33).

6. Adjust the upper/lower guides and the sup-

port bearings (refer to instructions beginning
on

Page 34).

7. Close the wheel covers.

8. Replace the table insert and table pin.

Installing Blade

1. DISCONNECT MACHINE FROM POWER!

2. Slide the blade through the table slot, ensur-

ing that the teeth are pointing down toward
the table.

Note: If the teeth will not point downward
in any orientation, the blade is inside-out.
Remove the blade, and twist it right side-out.

3. Slip the blade through the blade guides, and

mount it on the upper and lower wheels (see

Figure 75).

Blade changes entail removing the existing blade,
installing the new blade, then properly adjusting
the blade tension and tracking.

Removing Blade

1. DISCONNECT MACHINE FROM POWER!

2. Release blade tension by turning blade ten-

sion quick-release lever to the left (see

Figure 74).

3. Remove table insert and table pin (see

Figure 74). Adjust upper and lower guide
bearings as far away as possible from blade.

4. Open the upper and lower wheel covers, and

with gloved hands, slide the blade off of both
wheels.

5. Rotate the blade 90˚ and slide it through the

slot in the table to remove it.

Disconnect bandsaw from

power BEFORE changing

blade. Serious personal

injury could occur if

machine is started during

this procedure.

LACERATION HAZARD!

Bandsaw blades are sharp

and difficult to handle.

Wear heavy leather gloves

while handling to reduce

the risk of being cut.

Figure 74. Blade changing controls

(G0513X2 shown).

Table Pin

Blade

Guides

Table
Insert

Quick-Release

Lever

Содержание EXTREME G0513X2





































































































Результаты поиска

Содержание EXTREME G0513X2

Отзывы:

Бренды по названию

Популярные бренды

Grizzly EXTREME G0513X2, Руководство пользователя

Результаты поиска

Содержание EXTREME G0513X2

Отзывы:

Бренды по названию

Популярные бренды