Grizzly EXTREME G0513X2 Скачать руководство пользователя страница 48

Страница: 48 / 100

-46-

G0513 Series Bandsaws (Mfd. Since 08/22)

Figure 67. Guide post controls.

Guide Post

Lock Knob

Guide Post
Handwheel

Blade Guide

Assembly

Blade Guard

Guide Post

Blade Selection

Selecting the right blade requires a knowledge
of the various blade characteristics to match the
blade with the particular cutting operation.

Blade Terminology

Figure 68. Bandsaw blade components.

A. Kerf: The amount of material removed by the

blade during cutting.

B. Tooth Set: The amount each tooth is bent

left or right along the blade.

C. Gauge: The thickness of the blade.

D. Blade Width: The widest point of the blade

measured from the tip of the tooth to the back
edge of the blade.

E. Tooth Rake: The angle of the tooth face from

a line perpendicular to the length of the blade.

F. Gullet Depth: The distance from the tooth tip

to the bottom of the curved area (gullet).

G. Tooth Pitch: The distance between tooth

tips.

H. Blade Back: The distance between the bot-

tom of the gullet and the back edge of the
blade.

I. TPI: The number of teeth per inch measured

from gullet to gullet.

Setting Upper Blade

Guide Height

When cutting, the blade guides must always be
positioned so they just clear (no more than

⁄

the workpiece. The guide post, shown in

Figure

67, allows the upper blade guide assembly to be
quickly adjusted for height.

To adjust height of upper blade guides:

1. DISCONNECT MACHINE FROM POWER!

2. Loosen guide post lock knob (see Figure 67).

3. Use guide post elevation handwheel to adjust

height of guide post so that blade guide
assembly just clears (no more than

⁄

workpiece.

4. Retighten lock knob to secure setting.

Содержание EXTREME G0513X2





































































































Результаты поиска

Содержание EXTREME G0513X2

Отзывы:

Бренды по названию

Популярные бренды

Grizzly EXTREME G0513X2, Руководство пользователя

Результаты поиска

Содержание EXTREME G0513X2

Отзывы:

Бренды по названию

Популярные бренды