manualshive.com logo in svg

Grizzly EXTREME G0513X2, Руководство пользователя

Поделиться
Скачать
Grizzly EXTREME G0513X2 Скачать руководство пользователя страница 32

-30-

G0513 Series Bandsaws (Mfd. Since 08/22)

Test Run

Once assembly is complete, test run the machine 
to  ensure  it  is  properly  connected  to  power  and 
safety components are functioning correctly.

If you find an unusual problem during the test run, 
immediately stop the machine, disconnect it from 
power, and fix the problem BEFORE operating the 
machine again. The 

Troubleshooting table in the 

SERVICE section of this manual can help.

G0513, G0513A40 & G0513X2

DO NOT start machine until all preceding 

setup instructions have been performed. 

Operating an improperly set up machine 

may result in malfunction or unexpect-

ed results that can lead to serious injury, 

death, or machine/property damage.

Serious injury or death can result from 

using this machine BEFORE understanding 

its controls and related safety information. 

DO NOT operate, or allow others to operate, 

machine until the information is understood. 

The  Test  Run  consists  of  verifying  the  following: 
1)  The  motor  powers  up  and  runs  correctly,  and 
2)  the  switch  disabling  pin  disables  the  switch 
properly.

5.  Try to start machine by pressing switch but-

ton. Machine should NOT start.

— If  the  machine  does not  start,  the  safety 

feature of the switch disabling pin is work-
ing correctly.

— If  the  machine  does  start,  immediately 

turn  it 

OFF,  disconnect  power,  and  con-

tact customer service for assistance. The 
safety  feature  of  the  switch  disabling  pin 
is  NOT  working  properly  and  must  be 
replaced before further using the machine.

Shaft

Padlock

Figure 42. Disabling pin through switch button.

To test run machine:

1.  Clear all setup tools away from machine.

2.  Connect machine to power supply.

3.  Turn  machine  ON,  verify  motor  operation, 

and then turn machine 

OFF.

 

The  motor  should  run  smoothly  and  without 
unusual problems or noises.

4.  Insert disabling pin through switch button.

Содержание EXTREME G0513X2





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды