Grizzly EXTREME G0513X2 Скачать руководство пользователя страница 6

Страница: 6 / 100

-4-

G0513 Series Bandsaws (Mfd. Since 08/22)

A. Blade Tension Scale: Displays blade tension

using numbers 1–8. For reference only—after
proper tension for particular blade has been
determined.

B. Blade Tracking Window: Allows you to

monitor blade tracking on the wheel without
opening the wheel cover.

C. Blade Tension Handwheel: Increases/

decreases blade tension (refer to

Page 28

for more information).

D. Fence and Miter Gauge: Supports workpiece

for controlled straight or angled cuts.

E. Foot Brake (Model G0513X2BF): Quickly

stops bandsaw blade and turns motor

OFF.

Motor Brake

The Model G0513X2BF has a motor brake that
activates and quickly stops the blade when the
OFF button is used or the foot pedal is pressed.

Figure 3. Front controls

(G0513X2BF shown).

F. Wheel Cover Lock Knobs: Secure the

wheel covers.

G. Quick-Release Blade Tension Lever:

Adjusts blade tension for quick blade changes.

H. Tracking Control Knob and Lock Lever:

Moves and locks upper wheel tilt for blade
tracking.

I. Table Tilt Controls: Adjusts table tilt and

locks the table in place.

J. Magnetic Switch: Provides thermal overload

protection for the motor.

K. Lower Wheel Adjustment Hub: Used when

adjusting coplanarity of the wheels.

L. Guide Post Handwheel and Lock Knob:

Quickly moves the upper guide post to the
desired height; locks setting.

Figure 4. Rear controls

(G0513X2BF shown).

Front Controls

Rear Controls

Содержание EXTREME G0513X2





































































































Результаты поиска

Содержание EXTREME G0513X2

Отзывы:

Бренды по названию

Популярные бренды

Grizzly EXTREME G0513X2, Руководство пользователя

Результаты поиска

Содержание EXTREME G0513X2

Отзывы:

Бренды по названию

Популярные бренды