Grifco GSD-R2.4M Скачать руководство пользователя страница 30

Страница: 30 / 32

SYMPTOM

POSSIBLE CAUSES

SOLUTIONS

Switched (SW) Accessory
power remaining on

a) In limit setup mode

a) Learn the limits

Accessories connected to
Switch (SW) Accessory
power not working
correctly, turning off, or
resetting

a) Normal behavior

a) Move accessory to accessory power "ON"

Accessories connected to
Accessory power not
working correctly, turning
off, or resetting

a) Accessory power protector active
b) Defective control board

a) Disconnect all accessory powered devices and measure

accessory power voltage (should be 23 – 30 Vdc). If voltage is
correct, connect accessories one at a time, measuring
accessory voltage after every new connection

b) Replace defective control board

Quick Close not working
correctly

a) Quick Close setting incorrect
b) Interrupt loop detector
c) Defective Expansion board

a) Check that Quick Close setting is ON
b) Check operation of Interrupt Loop detector
c) Replace defective Expansion board

Anti-Tailgating not working
correctly

a) Anti-Tail setting incorrect
b) Interrupt loop detector
c) Defective Expansion board

a) Check that Anti-Tail setting is ON
b) Check operation of Interrupt Loop detector
c) Replace defective Expansion board

AUX Relay not working
correctly

a) AUX Relay setting incorrect

b) AUX Relay wiring incorrect

c) Defective Expansion board

a) Check AUX Relay switches settings
b) Check that wiring is connected to either N.O. and COM or to N.C.

and COM

c) Set AUX Relay to another setting and test. Replace defective

expansion board

TROUBLESHOOTING CHART continued...

TROUBLESHOOTING

Expansion Board

GSD-K1D8387-1CC

Gear Reducer

GSD-K32-37560-1

Antenna

GSD-K77-36541

Trolley

GSD-SP-Trolley

Acetyl Sliders
GSD-SP-Sliders

Main Control Board

GSD-K1D8389-1CC

Toroid Transformer

GSD-K204C0211

Bridge Rectiﬁer

GSD-K52C0481

APS Encoder with cable

GSD-K76-34697

Two 7AH batteries

GSD-K74-30762

Motor

GSD-K76-36398

EMI Board
120V/240V

GSD-K76-34728

APE Assembly with plastic tray

GSD-K1A6408-2

NOT SHOWN

GSD-K94-36540

Wiring Harness with product ID assembly

GSD-K94-34778

Wire harness between main control board and expansion board

GSD-K76-37858

Reset Button with product ID assembly

SERVICE & REPAIR PARTS

Содержание GSD-R2.4M

































Результаты поиска

Содержание GSD-R2.4M

Отзывы:

Похожие инструкции для GSD-R2.4M

Бренды по названию

Популярные бренды

Grifco GSD-R2.4M, Инструкция по эксплуатации

Результаты поиска

Содержание GSD-R2.4M

Отзывы:

Похожие инструкции для GSD-R2.4M

Бренды по названию

Популярные бренды