background image

27

CONTROL BOARD LEDS

OPERATOR ALARM CHART

STATUS LEDS

INPUT LEDS

INPUT LEDS

OPEN, CLOSE, & 
STOP INPUT

OFF

Input inactive

ON

Input active

BLINK

Input active on other operator

FIRE DEPT INPUT

OFF

Input inactive

ON

Input active

BLINK

Input active on other operator

EXIT

OFF

Input inactive

ON

Input active

BLINK

Input active on other operator

SHADOW

OFF

Input inactive

ON

Input active

BLINK

Input active on other operator

CLOSE EYES/
INTERRUPT

OFF

Input inactive

ON

Input active

BLINK

Input active on other operator

CLOSE EDGE

OFF

Input inactive

ON

Input active

BLINK

Input active on other operator

OPEN EYES/EDGE

OFF

Input inactive

ON

Input active

BLINK

Input active on other operator

LOCK

OFF

Maglock relay inactive

ON

Maglock relay active

STATUS LEDS

INPUT 
POWER

OFF

OFF state

ON

AC charger or Solar power available

BATT 
CHARGING

OFF

Not charging

ON

Three stage battery charging

TIMER

OFF

The timer is disabled

ON

The timer is enabled

MEDIUM BLINK (1 blink 
per second)

The timer is running

FAST BLINK (2 blinks 
per second)

The timer is paused

FASTEST BLINK (8 
blinks per second)

The timer is canceled

DOOR 
MOVING

OFF

The door is stopped

ON

The door is opening or closing

MEDIUM BLINK (1 blink 
per second)

One force event

FASTEST BLINK (8 
blinks per second)

Two force events

BATT LOW

OFF

No battery error

ON

Battery low

BLINK (1 blink per 
second)

Battery critically low

ACC PWR 
OVLD

OFF

OFF state

ON

Accessory overload protector opened

ALARM CHART

1 beep every 3 seconds 
during door operation

Operator is operating from battery power. AC power 
not connected

3 beeps every 3 seconds 
during door operation

Operator is operating from LOW battery power. AC 
power not connected. 

2 beeps every minute 
(constant)

Operator has encountered a double force based 
obstruction.

TROUBLESHOOTING

Содержание GSD-R2.4M

































Отзывы: