background image

32

Chamberlain Australia Pty Limited / Chamberlain New Zealand Limited (Chamberlain) is committed to manufacturing and supplying high quality goods.  As part of this 
commitment, we seek to provide reliable service and support for our goods and are pleased to provide you, the original purchaser, with this Chamberlain Limited Warranty.    
We also provide the following statement as required by the Australian Consumer Law:  In Australia, in addition to your rights under this Chamberlain Limited Warranty, our 
goods come with guarantees that cannot be excluded under the Australian Consumer Law.  You are entitled to a replacement or refund for a major failure and for 
compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality 
and the failure does not amount to a major failure. 

 
Chamberlain’s S-Drive Warranty   
Chamberlain warrants to the original purchaser of the Grifco S-Drive product (Operator) that:   
1  The S-Drive operator (including electric motor) is free from defects in materials and workmanship for a period of 2 years from the date of purchase or 100,000  
 

cycles (which ever comes first). Cycles can be determined by following the instructions in the manual. 

2  During the applicable Chamberlain Warranty period, if you are concerned that the Operator or electric motor may be defective, call our service centre on the toll  
 

free number below before removing the operator and a Chamberlain technician will diagnose the problem. Once the problem has been diagnosed, subject to your  

 

rights under the Australian Consumer Law with respect to major failures,

Chamberlain will provide you with:   
1  parts for “do-it-yourself” repairs; or   
2  shipping instructions for a factory repair or replacement.  
 

If a factory repair or replacement is required, provided the defective part or Operator is returned to Chamberlain well-packaged and in accordance with  

 

Chamberlain’s shipping instructions,

Chamberlain will, subject to your rights under the Australian Consumer Law with respect to major failures:   
1  in relation to the Operator, repair or, at its option where permissible, replace any defective part or Operator and return it to you at no cost; and  
2  Where the Operator has been installed by an authorised installer, you must call them for prompt on-site service.  Chamberlain will furnish replacement parts free of  
 

charge through the authorised installer.  A service fee for on-site service may apply. Repairs and replacement parts provided under this Chamberlain Limited  

 

Warranty are provided free of charge and are warranted for the remaining portion of the original warranty period. This Chamberlain Limited Warranty provides  

 

benefits which are in addition to your other rights and remedies as a consumer.  

 
Exclusions  
If our service centre determines that a warranty claim has been made in respect of a failure or defect arising under or out of any exclusion detailed below such that the 
claim is not covered under this Chamberlain Limited Warranty, we may, subject to your other rights and remedies as a consumer, charge you a fee to repair, replace and/or 
return the Operator to you. 

This Chamberlain Limited Warranty does not cover any failure of, or defect in, the Operator due to:  
1  non-compliance with the instructions regarding installation, operation, maintenance and testing of the Operator or of any product with which the Operator is used;  
2  any attempt by a person other than an authorised installer to change settings, repair, dismantle, reinstall or move the Operator to another location once it has  
 

been installed;  

3  tampering, neglect, abuse, wear and tear, accident, electrical storm, excessive use or conditions other than normal commercial use;  
4  use of the Operator in conjunction with controls which have not been supplied, or pre-approved, by Chamberlain;  
5  problems with, or relating to, the commercial door or commercial door hardware, including but not limited to the door springs, door rollers, door alignment, hinges,  
 

guides, slats and drums; or    

6  problems caused by electrical faults.

This Chamberlain Limited Warranty excludes perishable components such as acetyl sliders and batteries. 
If this Chamberlain Limited Warranty does not apply, you may have rights available to you under the Australian Consumer Law. 

Liability – Australia only  
Except as set out in the Australian Consumer Law (being Schedule 2 of the Competition and Consumer Act 2010) (as amended, consolidated or replaced):   
1  all other guarantees, warranties and representations in relation to the Operator or its supply are excluded to the extent that Chamberlain can lawfully exclude them; and  
2  under no circumstances will Chamberlain be liable for consequential, incidental or special damages arising in connection with the use, or inability to use, the Operator,  
 

other than those which were reasonably foreseeable as liable to result from the failure. 

Liability – New Zealand only  
Except as set out in the Fair Trading Act 1986 and the Consumer Guarantees Act 1993 (as amended, consolidated or replaced):  
1    all other guarantees, warranties and representations in relation to the Operator or its supply are excluded to the extent that Chamberlain can lawfully exclude them; and  
2    under no circumstances will Chamberlain be liable for consequential, incidental or special damages arising in connection with the use, or inability to use, the Operator,  
 

other than those which were reasonably foreseeable as liable to result from the failure.  

Note  
We request that you retain your sales docket or invoice as proof-of-purchase and attach it to this manual to enable you to establish the date of purchase in the unlikely 
event of a warranty service being required.  Chamberlain reserves the right to change the design and specifications of the Unit without prior notification.  Some features or 
accessories of the Unit may not be available in certain markets or areas.  Please check with your distributor. 

Chamberlain service centre contact details Australia  
Phone toll free 1800 474 326  
Fax toll free 1800 888 121  
Unit 1, 75 Epping Road North Ryde, NSW 2113 

Email [email protected] 

New Zealand  
Auckland phone 09 477 2823  
Phone toll free 0800 653 667  
Fax toll free 0800 653 663 

Website www.grifco.com.au or www.grifco.co.nz 

CHAMBERLAIN LIMITED WARRANTY - S-DRIVE OPERATOR

Ref: 01-38727D

Содержание GSD-R2.4M

































Отзывы: