Graco Reactor 2 E-30i Скачать руководство пользователя

Страница: 50 / 94

Advanced Setup Screens

Advanced setup screens enable users to set units, adjust values, set formats, and view software information
for each component. Press

to scroll through the Advanced setup screens, Once in the desired

Advanced setup screen, press

to access the ﬁelds and make changes. When changes are complete press

to exit edit mode.

Note

Users must be out of edit mode to scroll

through the Advanced setup screens.

Advanced Screen 1 — General

Use this screen to set the language, date format,

current date, time, setup screens password (0000 –

for none) or (0001 to 9999), and screen saver delay.

Advanced Screen 2 — Units

Use this screen to set the temperature units, pressure

units, volume units, and cycle units (pump cycles or

volume).

Advanced Screen 3 — USB

Use this screen to disable USB downloads/uploads,

disable USB log errors, enter the maximum number

of days to download data, and how frequently USB

logs are recorded. See

USB Data, page 77

Advanced Screen 4— Software

This screen displays the software part number and

software version for the Advanced Display Module,

USB Conﬁguration, Motor Control Module, and

Temperature Control Modules.

332636C

Содержание Reactor 2 E-30i































































































Результаты поиска

Содержание Reactor 2 E-30i

Отзывы:

Похожие инструкции для Reactor 2 E-30i

Бренды по названию

Популярные бренды

Graco Reactor 2 E-30i, Операция

Результаты поиска

Содержание Reactor 2 E-30i

Отзывы:

Похожие инструкции для Reactor 2 E-30i

Бренды по названию

Популярные бренды