Graco Reactor 2 E-30i Скачать руководство пользователя страница 83

Страница: 83 / 94

Alarms

There are two types of alarms that can occur on the system. Alarms are indicated by an icon the Run and

Information screens. See the information screen to see the latest alarm.
Warning
When present on system, a warning alarm will stop the generator.

Shutdown
When present on system, a shutdown alarm will stop the generator.

Warning

Icon

Description

Details

Battery High

Voltage

The DC Supply has risen above the high volts setting level for the duration of

the high battery volts timer.

Battery Low

Voltage

The DC Supply has fallen below the low volts setting level for the duration

of the low battery volts timer.

Fail To Stop

The module detected a condition that indicates that the engine is running when

it has been instructed to stop.

Flexible Sensor

The ﬂexible sensor warning alarm has been triggered.

Shutdown

Clear the alarm and remove the fault. Then press the stop button to reset the module.

Icon

Description

Details

Fail To Start

The engine has not ﬁred after the preset number of start attempts.

Generator High

Voltage Shutdown

The generator output voltage has risen above the preset level.

Generator Low

Voltage Shutdown

The generator output voltage has fallen below the preset level.

High Coolant

Temperature

Shutdown

The module detects that the engine coolant temperature has exceeded the high

engine temperature shutdown setting after the Safety On timer has expired.

Low Oil Pressure

Shutdown

The engine oil pressure has fallen below the low oil pressure trip setting level

after the Safety On timer has expired.

Over Frequency

Shutdown

The generator output frequency has risen above the preset level.

Under Frequency

Shutdown

The generator output frequency has fallen below the preset level.

332636C

Содержание Reactor 2 E-30i































































































Результаты поиска

Содержание Reactor 2 E-30i

Отзывы:

Похожие инструкции для Reactor 2 E-30i

Бренды по названию

Популярные бренды

Graco Reactor 2 E-30i, Операция

Результаты поиска

Содержание Reactor 2 E-30i

Отзывы:

Похожие инструкции для Reactor 2 E-30i

Бренды по названию

Популярные бренды