Graco Reactor 2 E-30i Скачать руководство пользователя страница 41

Страница: 41 / 94

Setup

Connect Battery

Improper battery installation or maintenance

may result in electric shock, chemical burns,

or explosion. Battery maintenance must only

be performed or supervised by personnel

knowledgeable of batteries and the required

precautions. Keep unauthorized personnel away

from batteries.

See

Technical Speciﬁcations, page 90

for battery

requirements and recommended battery size.
1. Secure battery (not supplied) to bracket with

strap.

Battery Connections

Figure 24

2. Connect battery cable from the engine starter

(ST) and chassis to the battery. Connect the

black cable to battery negative (-) and the red

cable to battery positive (+).

NOTICE

Always connect the red battery cable to battery

positive (+) and the black battery cable to the

battery negative (-). Failure to properly connect

the battery cable to the battery will damage the

fusible link when the engine control module is

turned ON. Do not bypass the fusible link when

damaged. The fusible link prevents damage

to other system components. See the system

repair manual for repair instructions.

Engine Starter Connections

Figure 25

3. Cover battery terminals with plastic caps (PC)

attached to supplied battery cables.

4. Verify battery was connected properly by

pressing OFF

on the engine control module

(PE) to “wake up” the controller screen. Do not

attempt to start the engine until all Setup steps

are complete. See Repair manual if engine

control module does not light up.

Add Fuel

1. Remove fuel cap (FS) and ﬁll fuel tank with no

more than 20 gallons (75 liters) of diesel fuel.

Replace cap. See Perkins engine manual for

approved diesel fuels.

2. Squeeze prime bulb (P) to prime engine. Press

the prime bulb repeatedly until fuel begins to

return to the fuel tank.

Figure 26

332636C

Содержание Reactor 2 E-30i































































































Результаты поиска

Содержание Reactor 2 E-30i

Отзывы:

Похожие инструкции для Reactor 2 E-30i

Бренды по названию

Популярные бренды

Graco Reactor 2 E-30i, Операция

Результаты поиска

Содержание Reactor 2 E-30i

Отзывы:

Похожие инструкции для Reactor 2 E-30i

Бренды по названию

Популярные бренды