Graco Reactor 2 E-30i Скачать руководство пользователя страница 37

Страница: 37 / 94

Setup

Setup

NOTICE

Proper system setup, startup, and shutdown

procedures are critical to electrical equipment

reliability. The following procedures ensure steady

voltage. Failure to follow these procedures will

cause voltage ﬂuctuations that can damage

electrical equipment and void the warranty.

Do not remove or separate the proportioner, engine

assembly, or power distribution box from the pallet.

Failure to leave the component mounting intact will

cause heating efﬁciency degradation, and potential

unsafe wiring and grounding.

Locate Reactor

1. Install hose rack, if ordered. See manual 3A1903

for detailed instructions.

2. Locate Reactor on a level surface that is

nonporous and diesel resistant, such as diamond

plate.

Note

Leave at least 1 ft. (0.3m) distance from

the engine side of the pallet to any wall

for engine maintenance access.

3. Do not expose Reactor to rain or below 20°F

(-7°C).

NOTICE

To ensure the heat exchanger control valves

open and close properly, do not store Reactor

below 20°F (-7°C).

4. If a wall will be installed between the proportioner

and generator, remove the fuel tank and battery

bracket. See

Trailer Setup Guidelines, page 38

5. To mount in a trailer, use forklift to move Reactor

by inserting the forks through the Reactor pallet

frame. It is recommended to lift from the engine

side. Bolt pallet directly to trailer frame.

Note

Use Pallet Support Kit 24L911 (rollers not

included) to relocate pallet to mounting

location when forks are unavailable. See

kit manual for instructions.

NOTICE

Keep the vent holes in the bottom of the

proportioner cabinet open. Make sure there is

unobstructed incoming air for the cooling fan at the

top of the proportioner cabinet that blows air up into

the electric motor. Failure to provide unobstructed

incoming air can cause the motor to overheat.

332636C

Содержание Reactor 2 E-30i































































































Результаты поиска

Содержание Reactor 2 E-30i

Отзывы:

Похожие инструкции для Reactor 2 E-30i

Бренды по названию

Популярные бренды

Graco Reactor 2 E-30i, Операция

Результаты поиска

Содержание Reactor 2 E-30i

Отзывы:

Похожие инструкции для Reactor 2 E-30i

Бренды по названию

Популярные бренды