Graco Reactor 2 E-30i Скачать руководство пользователя

Страница: 63 / 94

Spraying

Spraying

1. Engage gun piston safety lock and close gun

ﬂuid inlet valves A and B.

Fusion

Probler

2. Attach gun ﬂuid manifold. Connect gun air line.

Open air line valve.

3. Adjust the gun air regulator on the proportioner

control panel to desired gun air pressure. Do not

exceed 130 psi (0.2 MPa, 2 bar).

4. Set PRESSURE RELIEF/SPRAY valves (SA,

SB) to SPRAY

5. Check that heat zones are on and temperatures

are on target, see

Home screen, page 53

6. Verify that the engine temperature is at least up

to the minimum operation temperature range.

The fan will start running when the engine has

reached maximum temperature.

7. Open ﬂuid inlet valves.

8. Press

to start motor and pumps.

9. Check ﬂuid pressure gauges (GA, GB) to

ensure proper pressure balance. If imbalanced,

reduce pressure of higher component by

slightly turning PRESSURE RELIEF/SPRAY

valve for that component toward PRESSURE

RELIEF/CIRCULATION

until gauges show

balanced pressures.

332636C

Содержание Reactor 2 E-30i































































































Результаты поиска

Содержание Reactor 2 E-30i

Отзывы:

Похожие инструкции для Reactor 2 E-30i

Бренды по названию

Популярные бренды

Graco Reactor 2 E-30i, Операция

Результаты поиска

Содержание Reactor 2 E-30i

Отзывы:

Похожие инструкции для Reactor 2 E-30i

Бренды по названию

Популярные бренды