Graco Reactor 2 E-30i Скачать руководство пользователя страница 5

Страница: 5 / 94

WARNING

THERMAL EXPANSION HAZARD
Fluids subjected to heat in conﬁned spaces, including hoses, can create a rapid rise in pressure

due to the thermal expansion. Over-pressurization can result in equipment rupture and serious

injury.
• Open a valve to relieve the ﬂuid expansion during heating.
• Replace hoses proactively at regular intervals based on your operating conditions.

PRESSURIZED ALUMINUM PARTS HAZARD
Use of ﬂuids that are incompatible with aluminum in pressurized equipment can cause serious

chemical reaction and equipment rupture. Failure to follow this warning can result in death,

serious injury, or property damage.
• Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon

solvents or ﬂuids containing such solvents.

• Many other ﬂuids may contain chemicals that can react with aluminum. Contact your material

supplier for compatibility.

PLASTIC PARTS CLEANING SOLVENT HAZARD
Many solvents can degrade plastic parts and cause them to fail, which could cause serious

injury or property damage.
• Use only compatible water-based solvents to clean plastic structural or pressure-containing

parts.

• See Technical Data in this and all other equipment instruction manuals. Read ﬂuid and

solvent manufacturer’s MSDSs and recommendations.

332636C

Содержание Reactor 2 E-30i































































































Результаты поиска

Содержание Reactor 2 E-30i

Отзывы:

Похожие инструкции для Reactor 2 E-30i

Бренды по названию

Популярные бренды

Graco Reactor 2 E-30i, Операция

Результаты поиска

Содержание Reactor 2 E-30i

Отзывы:

Похожие инструкции для Reactor 2 E-30i

Бренды по названию

Популярные бренды