Graco Reactor 2 E-30i Скачать руководство пользователя | Manualshive

Страница: 6 / 94

background image

WARNING

EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not operate the unit when fatigued or under the inﬂuence of drugs or alcohol.
• Do not exceed the maximum working pressure or temperature rating of the lowest rated

system component. See Technical Data in all equipment manuals.

• Use ﬂuids and solvents that are compatible with equipment wetted parts. See Technical Data

in all equipment manuals. Read ﬂuid and solvent manufacturer’s warnings. For complete

information about your material, request MSDS from distributor or retailer.

• Do not leave the work area while equipment is energized or under pressure.
• Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.
• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine

manufacturer’s replacement parts only.

• Do not alter or modify equipment. Alterations or modiﬁcations may void agency approvals

and create safety hazards.

• Make sure all equipment is rated and approved for the environment in which you are using it.
• Use equipment only for its intended purpose. Call your distributor for information.
• Route hoses and cables away from trafﬁc areas, sharp edges, moving parts, and hot surfaces.
• Do not kink or over bend hoses or use hoses to pull equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
BATTERY HAZARD
The battery may leak, explode, cause burns, or cause an explosion if mishandled.
• Only use the battery type speciﬁed for use with the equipment. See Technical Data.
• Battery maintenance must only be performed or supervised by personnel knowledgeable of

batteries and the required precautions. Keep unauthorized personnel away from battery.

• When replacing the battery, use the same lead-acid automotive battery, with 800 CCA

minimum, speciﬁed for use with the equipment. See Technical Data.

• Do not dispose of battery in ﬁre. The battery is capable of exploding.
• Follow local ordinances and/or regulations for disposal.
• Do not open or mutilate the battery. Released electrolyte has been known to be harmful to

the skin and eyes and to be toxic.

• Remove watches, rings, or other metal objects.
• Only use tools with insulated handles. Do not lay tools or metal parts on top of battery.
MOVING PARTS HAZARD
Moving parts can pinch, cut or amputate ﬁngers and other body parts.
• Keep clear of moving parts.
• Do not operate equipment with protective guards or covers removed.
• Pressurized equipment can start without warning. Before checking, moving, or servicing

equipment, follow the Pressure Relief Procedure and disconnect all power sources.

6

332636C

«
...
4
5
6
7
8
...
»

Содержание Reactor 2 E-30i































































































Отзывы:

Нет отзывов

Похожие инструкции для Reactor 2 E-30i

Бренд: Water Worker Страницы: 24

Бренд: salmson Страницы: 16

Бренд: Reefe Страницы: 12

Бренд: Davey Страницы: 20

Бренд: ProMinent Страницы: 81

AQUAPRO AP1000FP

Бренд: Aquatec Страницы: 2

SMART GEYSER 2330-03

Бренд: Simer Страницы: 12

Бренд: Kayoba Страницы: 6

Бренд: Atlantic Страницы: 20

Бренд: Takagi Страницы: 56

Бренд: RBI Страницы: 44

Бренд: Simer Страницы: 24

Бренд: XtremepowerUS Страницы: 14

Бренд: Cornelius Страницы: 19

Бренд: Homa Страницы: 40

Бренд: EBARA Страницы: 51

Бренд: Wallace Pumps Страницы: 5

Бренд: Varian Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды