Graco Reactor 2 E-30i Скачать руководство пользователя

Страница: 62 / 94

Fluid Circulation

Circulation Through Gun Manifold

NOTICE

To prevent equipment damage, do not circulate

ﬂuid containing a blowing agent without consulting

with your material supplier regarding ﬂuid

temperature limits.

Note

Circulating ﬂuid through the gun manifold

allows rapid preheating of the hose.

1. Install gun ﬂuid manifold (P) on accessory

circulation kit (CK). Connect high pressure

circulation lines (R) to circulation manifold.

The Fusion AP gun manifold is shown.

Gun

Manual

246362

Fusion AP

309818

256566

Fusion CS

313058

2. Route circulation lines back to respective

component A or B supply drum. Use hoses

rated at the maximum working pressure of this

equipment.

3. Follow procedures from

Startup, page 57

4. Turn main power switch on

5. Set temperature targets. See

Targets, page 53

6. Press

to circulate ﬂuid in jog mode until

A and B temperatures reach targets. See

Jog Mode, page 62

for more information about

jog mode.

Jog Mode

Jog mode has two purposes:
• Speed ﬂuid heating during circulation.
• Ease system ﬂushing and priming.

1. Turn main power switch on

2. Press circulate

to enter jog mode.

3. Press up or down

to change jog speed

(J1 through J20).

Note

Jog speeds correlate to 3-60% of motor

speed, but will not operate over 700 psi

(4.9 MPa, 49 bar) for either A or B.

4. Press

to start motor.

To stop the motor and exit jog mode press

332636C

Содержание Reactor 2 E-30i































































































Результаты поиска

Содержание Reactor 2 E-30i

Отзывы:

Похожие инструкции для Reactor 2 E-30i

Бренды по названию

Популярные бренды

Graco Reactor 2 E-30i, Операция

Результаты поиска

Содержание Reactor 2 E-30i

Отзывы:

Похожие инструкции для Reactor 2 E-30i

Бренды по названию

Популярные бренды