Graco Reactor 2 E-30i Скачать руководство пользователя страница 65

Страница: 65 / 94

Spraying

Manual Hose Heat Mode

If the system produces the T6DH sensor error hose

alarm or the T6DT sensor error TCM alarm, use

manual hose heat mode until the hose RTD sensor

can be repaired.
Do not use Manual Hose Mode for extended periods

of time. The system performs best when the hose

has a valid RTD and can operate in temperature

control mode. If a hose RTD breaks, the ﬁrst priority

is to ﬁx the RTD. Manual Hose Mode can help ﬁnish

a job while waiting for repair parts.

Enable Manual Hose Mode

1. Disconnect the hose RTD sensor from the TCM.
2. Enter Setup Mode and navigate to System

Screen 2.

3. Select Enable Manual Hose Mode.

Note

When manual hose mode is enabled, the

manual hose mode advisory EVCH-V

will appear.

4. Enter Run Mode and navigate to the Target

screen. Set the desired hose current.

Hose Current Settings Hose Current

Default

20A

Maximum

37A

Note

Until the RTD sensor is repaired, the

T6DH sensor error alarm will display

each time the system is powered up.

5. Navigate back to the Run Mode Home screen.

The hose now displays a current instead of a

temperature.

332636C

Содержание Reactor 2 E-30i































































































Результаты поиска

Содержание Reactor 2 E-30i

Отзывы:

Похожие инструкции для Reactor 2 E-30i

Бренды по названию

Популярные бренды

Graco Reactor 2 E-30i, Операция

Результаты поиска

Содержание Reactor 2 E-30i

Отзывы:

Похожие инструкции для Reactor 2 E-30i

Бренды по названию

Популярные бренды