Graco Reactor 2 E-30i Скачать руководство пользователя

Страница: 47 / 94

Operation

Operation

1. Turn the main power switch ON. The Graco logo

will display until communication and initialization

is complete.

2. Press the on/off button

3. Verify the machine is active and the System

Status LED is illuminated green, see

Advanced Display Module (ADM), page 21

. If

the System Status LED is not green, press the
ADM Power On/Off (A) button

. The System

Status LED will illuminate yellow if the machine

is disabled.

Initial System Setup

Perform the following tasks to fully setup your system.
1. Select pressure for the Pressure Imbalance

Alarm to activate. See

System Screen , page 51

2. Enter, enable, or disable recipes. See

Recipes Screen, page 56

3. Set general system settings. See

Advanced Screen 1 — General, page 50

4. Set units of measure. See

Advanced Screen 2 — Units, page 50

5. Set USB settings. See

Advanced Screen 3— USB, page 50

6. Set target temperatures and pressure. See

Targets, page 53

7. Set component A and component B supply

levels. See

Maintenance, page 54

8. Ensure engine is at operating temperature on the

home screen.

332636C

Содержание Reactor 2 E-30i































































































Результаты поиска

Содержание Reactor 2 E-30i

Отзывы:

Похожие инструкции для Reactor 2 E-30i

Бренды по названию

Популярные бренды

Graco Reactor 2 E-30i, Операция

Результаты поиска

Содержание Reactor 2 E-30i

Отзывы:

Похожие инструкции для Reactor 2 E-30i

Бренды по названию

Популярные бренды