GraceWood The Sturdy-Lite Скачать руководство пользователя страница 28

Страница: 28 / 30

-28-

Attach Quilt Backing to Take-

Up Rail with Fabrifast Tubing

Fold extra batting out of your way.

Place Batting on top of Backing.

Batting goes over Back Rail, and

under Middle Rail

STEP 4: INSTALL QUILT BOTTOM TO THE TAKE-UP RAIL

• Now take the end of the quilt batting hanging from the back rail, and pull it under the middle rail,

to the cloth leader on the take-up rail.

• Pin this end to the take-up rail.

STEP 5: BATTING OVER THE BACKING

• A light, bonded batting is recommended.

• Take one end of the batting and insert it over the back rail and down under the middle rail. Pull it

through so the end of the batting lines up over the backing. Smooth out any wrinkles.

•

The other end of the batting can hang freely over the back pole and roll off the floor.

Содержание The Sturdy-Lite































Результаты поиска

Содержание The Sturdy-Lite

Отзывы:

Похожие инструкции для The Sturdy-Lite

Бренды по названию

Популярные бренды

GraceWood The Sturdy-Lite, Руководство пользователя

Результаты поиска

Содержание The Sturdy-Lite

Отзывы:

Похожие инструкции для The Sturdy-Lite

Бренды по названию

Популярные бренды