GraceWood The Sturdy-Lite Скачать руководство пользователя страница 27

Страница: 27 / 30

-27-

Quilt Top

Good Side Up

Secure to Middle Rail with Fabrifast Tubing

• With the “good” side of the quilt top facing up, pin it to

your cloth leader attached to the middle rail, following

the same guidelines as the quilt bottom

• Roll your quilt top onto the middle rail, so that the

fabric rolls under and onto the rail, as pictured.

Again note that the ratchet stop will prevent

you from rolling the wrong way.

• Again, make sure you roll the

fabric straight.

• As you smooth out any

wrinkles, again be very

careful not to stretch or pull the

fabric excessively.

STEP 3: QUILT TOP TO MIDDLE RAIL

• Match the back and front ends of the quilt top

with the bottom you have installed.

• Be sure you line up your quilt top so it is in line

with the quilt bottom.

Содержание The Sturdy-Lite































Результаты поиска

Содержание The Sturdy-Lite

Отзывы:

Похожие инструкции для The Sturdy-Lite

Бренды по названию

Популярные бренды

GraceWood The Sturdy-Lite, Руководство пользователя

Результаты поиска

Содержание The Sturdy-Lite

Отзывы:

Похожие инструкции для The Sturdy-Lite

Бренды по названию

Популярные бренды