manualshive.com logo in svg

Gow-Mac 400 Series, Руководство по эксплуатации

Поделиться
Скачать
Gow-Mac 400 Series Скачать руководство пользователя страница 6

GOW-MAC Instrument Co.           Series 400 / 402 Gas Chromatograph Operating Manual

May 2017, Rev. 7

6

LIABILITY  

Buyer assumes all responsibility for warning and protecting its employees and independent contractors with respect 

to all hazards to persons and property in any way connected with the Equipment and the use thereof. Seller’s liability for any claim 
of any kind hereunder, whether or not based on contract, tort (including negligence), strict liability, warranty, or any other grounds, 
shall not exceed the purchase price of the Equipment or the portion of the purchase price attributable to any part or parts of the 
Equipment in respect to which such claim is made. Seller shall not be liable for any special, indirect, incidental, or consequential 
damages. Without limiting the generality of the foregoing, Seller shall have no liability with respect to the results obtained by use 
of the Equipment, whether in terms of product condition, operating cost, general eff ectiveness, success or failure, or regardless of 
any statement made in any written proposal submitted by Seller. It is expressly understood that any technical advice furnished by 
Seller with reference to the Equipment is given gratis and Seller assumes no obligation or liability for the advice given or results 
obtained, all such advice being given and accepted at Buyer’s risk. Each party hereby agrees to indemnify and hold the other party 
harmless from any actions, lawsuits, demands, claims, losses, expenses, costs, including but not limited to legal fees, and damages 
arising from the injury, illness or death of the indemnifying party’s employees in any way related to the Equipment, whether or not 
such injury, illness, or death is claimed to have been caused by, resulted from, or was in any way connected with the negligence 
of the party to be indemnifi ed.

PROPRIETARY INFORMATION 

 

Buyer agrees to maintain all proprietary information disclosed by Seller, including such 

proprietary information obtainable upon examination of the Equipment, in confi dence and to refrain from any disclosure thereof to 
any third party (including any affi  liate of Buyer), for any purpose, without the prior written consent of Seller. Buyer agrees to use 
said proprietary information solely for purposes of maintaining and operating the Equipment, and to refrain from any use thereof to 
design, construct, have constructed and/or operate any duplication or modifi cation of the Equipment, or from any other use thereof, 
without the prior written consent of Seller.

IMPORTANT INFORMATION

These instructions are written for personnel operating the GOW-MAC

®

 Series 400 Isothermal TCD Gas 

Chromatograph. Read and understand the safety precautions in this manual to become familiar with the safe 
practices for operating this equipment.

Dangers, Warnings, Cautions, and Notes

Dangers, Warnings, Cautions, and Notes appear throughout this manual. A sample of each statement 
appears below. Within each sample, a defi nition of the statement type and its purpose is given.

 

DANGER

!

 

DANGERS alert you to an immediate hazard that causes serious injury or death 
and requires special precautions to be taken.

 

WARNING

!

 

WARNINGS alert you to a potential hazard that causes serious injury or death 

under certain conditions.

 

CAUTION

 

CAUTIONS alert you to a non-immediate or potential hazard or an unsafe 
practice that presents a minor threat of personal injury or damage to 
equipment, data, or processes.

          

NOTE

&

  

NOTES emphasize or remind you of an important piece of information.

Содержание 400 Series

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды