Gow-Mac 400 Series Скачать руководство пользователя страница 37

Страница: 37 / 64

Series 400 / 402 Gas Chromatograph Operating Manual GOW-MAC Instrument Co.

May 2017, Rev. 7

B. Procedure for Removing and Replacing Loops

1. Unscrew loop mounting ﬁ ttings (2) and remove loop.

2. Insert new loop and tighten ﬁ ttings.

6.6 Pneumatically Actuated Valves

ACT. AIR IN

SAMPLE OUT

SAMPLE IN

VENT

SAMPLE OUT

SAMPLE IN

ACT. AIR IN

MIN. PRESSURE 15 PSIG

INLET

Sample Gas regulated to 20 psig.

Set flow to about 100 ccpm using
customer supplied needle valve.

Two micron (2

) filter.

Valve Actuator Gas

Compressed Air regulated

to 30-50 psig.

FREE OF OIL AND WATER!

Carrier

Gas

Sample

Gas

Carrier Gas regulated to
20 to 75 psig depending
on column length.

Two micron (2

) filter.

Air

Figure 6-1: Typical Setup. Your's may vary. Refer to enclosed ﬂ ow diagram.

A. Pneumatically actuated gas sample valves require compressed air gas that is

free of oil

and water

to function. An air pressure of 30-50 psi is recommended to fully drive the

valves.

B. A TTL Interface PCB enables the operator to control the pneumatic actuated valves that

are installed in the GC via an external controller, i.e., computing software or computing

integrator.

This external controller must be able to supply an active high (+5 V) TTL signal to the

corresponding Valve Actuator (TTL) Cable Connection located on the GC's Valve

Housing. This +5 V signal must be kept “ON” for the entire period of time the user wants to

keep the valve(s) actuated.

C. Connect the Interface Cable provided to the VALVE ACTUATORS Terminal Strip located

on the back of the

Valve Housing(s)

. Moving top to bottom along the strip, attach the color

coded wires in the following sequence:

Содержание 400 Series

































































Результаты поиска

Содержание 400 Series

Отзывы:

Бренды по названию

Популярные бренды

Gow-Mac 400 Series, Руководство по эксплуатации

Результаты поиска

Содержание 400 Series

Отзывы:

Бренды по названию

Популярные бренды