Gow-Mac 400 Series Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 64

Gow-Mac 400 Series Скачать руководство пользователя страница 13

13

Series 400 / 402 Gas Chromatograph Operating Manual GOW-MAC Instrument Co.

May 2017, Rev. 7

Chapter 2 - Specifi cations

The Series 400/402 Gas Chromatograph is a rugged, compact, thermal conductivity GC designed
for high capability performance while withstanding rough, student or industrial use.

The ﬂ ow system consists of two needle valves for accurate column ﬂ ow control, dual injection ports,
dual columns and exits.

Temperature of injection ports, column oven and detector oven can be individually controlled. The
detector is housed in an easily accessible oven assembly. The thermal conductivity detector (TCD)
contains four 32 ohm, Rhenium-tungsten (WX) hotwire ﬁ laments (standard).

The Series 400-P/402-P GC is equipped with a microscale preparative accessory system. This GC
is equipped with a microscale prep detector with outlet temperature control. The system is based on
the description given by Mayo, Pike, et. al., in

Microscale Organic Laboratory

, E. Wiley & Son,

N. Y., 1986.

Dimensions

Overall

16.50" H (410 mm) x 12.00" W (300 mm) x 11.00" D (270 mm)

Weight

27 lbs. (12.26 kg)

Power Requirements

Series 400: 110-120 VAC, 50/60 Hz: 600 W (max), 10 A circuit breaker

Series 402: 220-240 VAC, 50/60 Hz, 600 W (max), 4 A circuit breaker

Column Oven

Dimensions:

16.19 cm H x 25.40 cm W x 18.41 cm D

Volume:

7570.67 cm

3

V

Temperature Range:

Ambient to 400 °C

Temperature Control:

solid state, time proportioning, RTD sensors, direct reading, ambient

to 400 °C

Temperature Readout: 3-1/2 digit LCD digital meter

Protection Circuit:

shuts the column oven oﬀ if the temperature rises to 30 °C over set

point

Detector Outlet

[optional with preparative detector (Series 400-P/402-P)]

Temperature Range:

Ambient to 350 °C

Temperature Control:

phase control, RTD sensor, ambient to 350 °C

Temperature Readout:

3-1/2 digit LCD digital meter

Operating Temperature: 20 °C above column temperature

Oven Fittings

Accommodates 1/8" or 1/4" o.d. metal or glass columns

Oven Capacity

Two 1/4" o.d. x 12' columns or correspondingly longer lengths of 1/8" o.d.

«
...
11
12
13
14
15
...
»

Содержание 400 Series

































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды