Gow-Mac 400 Series Скачать руководство пользователя страница 24

Страница: 24 / 64

GOW-MAC Instrument Co. Series 400 / 402 Gas Chromatograph Operating Manual

May 2017, Rev. 7

INJECTION PORT "A"

FLOW ADJUSTMENT "A"

COLUMN TEMPERATURE CONTROL

: Selects the isothermal temperature of the column

oven. The temperature may be monitored on the

DIGITAL PANEL METER

when the COL.

TEMP. Button is pressed (see 7b below). Knob is "locking type". Push locking ring "in" to turn
knob.

DETECTOR TEMPERATURE CONTROL

: Selects the temperature of the detector oven. The

temperature may be monitored on the

DIGITAL PANEL METER

when the DET. TEMP. Button

is pressed (see 7c below). Knob is "locking type". Push locking ring "in" to turn knob.

INJECTION PORT TEMPERATURE CONTROL

: Selects the temperature of the injection

ports. The temperature may be monitored on the

DIGITAL PANEL METER

when the INJ.

PORT. TEMP. Button is pressed (see 7a below). Knob is "locking type". Push locking ring "in"
to turn knob.

DIGITAL PANEL METER

: Displays the value of the operation function chosen by the

SELECTOR BUTTONS.

SELECTOR BUTTONS:

a. INJECTION PORT TEMPERATURE (°C): selects injection port temperature to appear on

the DIGITAL PANEL METER.

b. COLUMN OVEN TEMPERATURE (°C): selects column temperature reading to appear on

the DIGITAL PANEL METER.

c. DETECTOR TEMPERATURE (°C): selects detector temperature reading to appear on the

DIGITAL PANEL METER.

d. DETECTOR CURRENT: selects detector current reading to appear on the DIGITAL

PANEL METER.

e. SET (IN)/ACTUAL (OUT): selects either actual or set-point parameters for any of the

functions (a-d) above. This button should be left in the "ACTUAL" (OUT) position

EXCEPT

when settings are being changed.

GC POWER SWITCH

: Supplies line power to the GC when depressed and lit.

POLARITY SWITCH

: Selects polarity (+/-) of the detector output signal. Allows use of each

column without having to change the wiring to reverse polarity on the recorder.

10.

DETECTOR CURRENT SWITCH:

allows the detector to be turned ON/OFF without shutting

down the entire instrument.

11.

ZERO CONTROL

: Adjusts the detector output level for zeroing the baseline of the

recorder. Recorder should be zeroed ﬁ rst with short input.

Содержание 400 Series

































































Результаты поиска

Содержание 400 Series

Отзывы:

Бренды по названию

Популярные бренды

Gow-Mac 400 Series, Руководство по эксплуатации

Результаты поиска

Содержание 400 Series

Отзывы:

Бренды по названию

Популярные бренды