Gow-Mac 400 Series Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 64

Gow-Mac 400 Series Скачать руководство пользователя страница 29

29

Series 400 / 402 Gas Chromatograph Operating Manual GOW-MAC Instrument Co.

May 2017, Rev. 7

C. Observe the chromatograms for peak separations, peak heights, and retention times.

Adjust controls accordingly.

4.7 Standby and Overnight Conditions

When the GC is used intermittently during the day or is needed right away the next morning, it
is recommended that the GC be kept in "standby" condition. This keeps the instrument ready
to use without waiting for a long equilibration period. Proceed as follows:

A. Push the

SET

Button and

DETECTOR

Button "IN".

B. Turn

DETECTOR CURRENT CONTROL

counterclockwise (CCW) until the

DIGITAL

PANEL METER

displays between 28 to 40. Then turn

CURRENT SWITCH

to "oﬀ '

position.

C. Reduce the carrier gas ﬂ ow from 40 psig to 20 psig to save gas consumption

(FLOW

RATE MUST NOT FALL BELOW 20 psig).

4.8 Shutdown Procedure

The following sequence of steps should be followed in the given sequence to insure proper
cool-down of your GC and longer life of the detector ﬁ laments.

A. Push the

SET

and

DETECTOR CURRENT

Buttons "IN".

B. Turn the

DETECTOR CURRENT CONTROL

counterclockwise until the

DIGITAL PANEL

METER

displays between 28 to 40. Then turn the

CURRENT SWITCH

to "oﬀ " position.

C. Repeat Steps A & B above for the

COLUMN, DETECTOR

, and

INJECTOR

.

D. Let the GC cool down for 30 minutes. For quicker oven cool down, the column oven lid

may be lifted and left open.

E. Let the GC cool down until the detector temperature reaches 90 °C.

The ﬁ laments

may burn out if the instrument is not left to cool properly.

WARNING

!

IF THE INSTRUMENT IS NOT LEFT TO COOL PROPERLY,

THE DETECTOR FILAMENTS MAY BURN OUT (OXIDIZE).

F. Elute all samples from the column BEFORE the columns cool down.

G. Shut ac power

OFF

.

H. Turn helium or other carrier gas "OFF".

«
...
27
28
29
30
31
...
»

Содержание 400 Series

































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды