manualshive.com logo in svg

Gow-Mac 400 Series, Руководство по эксплуатации

Поделиться
Скачать
Gow-Mac 400 Series Скачать руководство пользователя страница 52

GOW-MAC Instrument Co.           Series 400 / 402 Gas Chromatograph Operating Manual

May 2017, Rev. 7

52

 

 

4. 

Power Pass Transistor

: All direct current is passed through the Silicon Power

Transformer.

9.12  Technical Assistance and Service

 

Call our Repair Department at (610) 954-9000 to receive technical assistance, an estimate for 
repair, as well as a Health and Safety form (see back of this manual or, if it is missing, contact 
us and we will fax one over to you or visit our website to download the form.) Once we receive 
a completed Health & Safety form, an RMA number will be assigned and further information 
will be e-mailed to you so that you can to send the instrument or TCD back to us. Instruments 
or TCDs received without a completed Health & Safety form or RMA will not be permitted into 
our facility.

 

Display the RMA number on your shipping label to insure prompt attention upon arrival at 
GOW-MAC.

 

 

 

   

 

 

GOW-MAC Instrument Co.

 

 

   

 

 

Attn: Repair Dept, RMA# _______

 

 

 

   

 

 

277 Brodhead Road

 

 

 

   

 

 

Bethlehem, PA  18017-8600

 

Please include a contact person, phone number, service required and a P.O. number.  We are 
also able to furnish an estimate prior to repairs if this is required.

Содержание 400 Series

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды