manualshive.com logo in svg

Gow-Mac 400 Series, Руководство по эксплуатации

Поделиться
Скачать
Gow-Mac 400 Series Скачать руководство пользователя страница 33

33

Series 400 / 402 Gas Chromatograph Operating Manual             GOW-MAC Instrument Co.

May 2017, Rev. 7

 

!

IMPORTANT

 

IT IS MOST IMPORTANT THAT THE ADAPTER BE THREADED 
ONTO THE EXIT PORT COMPLETELY. THE END OF THE EXIT 
PORT MUST EXTEND WELL INTO THE GROUND STANDARD 
TAPERED PART OF THE ADAPTER WHEN IT IS ATTACHED 
TO THE EXIT PORT. THIS ARRANGEMENT WILL ALLOW 
THE END OF THE EXIT PORT TO BUTT SNUGLY AGAINST 
THE COLLECTION TUBE WHEN FULLY ASSEMBLED. IT IS 
ABSOLUTELY ESSENTIAL THAT THIS CONTACT IS MADE.

 

 

2.  When the recorder indicates that the fraction to be collected is approaching the end of  
 

the column, the collection tube (previously cleaned and oven dried) is seated in to the  

 

adapter.

 

 

3.  Place a collection tube into the adapter by rotating the collection tube while inserting it

into the adapter. If too much pressure is applied the collection tube will unseat. It is
important to practice rotating the collection tube 

GENTLY

 to obtain just enough 

pressure to make a good seal, but not enough to unseat the joint.

 

 

4.  The preparative GC fraction is now collected as it passes through the exit port into the

collection tube. Effi  cient collection is facilitated (diminished aerosol formation) by the
large heat sink aff orded by the mass of the stainless steel adapter. Once the recorder
indicates that the fraction is off  the column, the collection tube should be detached 
from the adapter.

 

 

5.  The collection tube should then be connected to a tared 100 mL conical vial and 

placed in a centrifuge tube (cotton padding around the collection tube and bottom of 
the vial is recommended - refer to Figure 5-2). Centrifuge the assembly. The collected 
GC fraction has now been collected. Detach the vial from the collection tube, cap the 
vial and weight it. 

 

 

 

 

 

 

 

 

        

 

GC Fraction

Collection Tube

12 mL

Centrifuge Tube

Cotton

Plug

100 

μ

L

Conical Vial

Sample

Collects

Here

GC Collection Tube

GC Connection

Adapter

Vial,

Conical Reaction

(Threaded)

Figure 5-2

Microscale Prep Glassware

Содержание 400 Series

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды