manualshive.com logo in svg

Gow-Mac 400 Series, Руководство по эксплуатации

Поделиться
Скачать
Gow-Mac 400 Series Скачать руководство пользователя страница 3

3

Series 400 / 402 Gas Chromatograph Operating Manual             GOW-MAC Instrument Co.

May 2017, Rev. 7

Contents

Disclaimers  ........................................................................................................................... 5
Important Information  ........................................................................................................... 6
Warranty ................................................................................................................................ 7
Important Warning  ................................................................................................................ 9
Important: Gas Flow Adjustment Note  ................................................................................ 10

Chapter 1 - Safety Precautions ............................................................................................11

Chapter 2 - Specifi cations ................................................................................................... 13

Chapter 3 - Installation ........................................................................................................ 15

Chapter 4 - Operation .......................................................................................................... 23

Chapter 5 - Microscale Prep ................................................................................................ 31

Chapter 6 - Valves ............................................................................................................... 35

Chapter 7 - Software ........................................................................................................... 39

Chapter 8 - Experimental Run Through ............................................................................... 41

Chapter 9 - Maintenance ..................................................................................................... 47

Chapter 10 - Replacement Parts ......................................................................................... 53

Chapter 11 -  Mechanical Drawings ..................................................................................... 55

Содержание 400 Series

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды