background image

CHAP TER  1

IN TRO DUC TION  AND  GEN ERAL  IN FOR MA TION

1-1    IN TRO DUC TION

The  HGU-84/P Com mer cial Hel met As sem bly is de signed to pro vide eye, ear, and head 
pro tec tion when prop erly as sem bled and fit ted to the aircrew mem ber.  It has a light -
weight hel met shell con structed of graph ite, bal lis tic ny lon, fi ber glass, and ep oxy resin. 
The hel met as sem bly, avail able in four sizes (me dium, large, X-large, and X-large
wide), is form-fit ted.  Its sta bil ity is en hanced by an in te grated chin/nape strap as sem bly.  
The hel met as sem bly also houses the head set com mu ni ca tions and al lows for the use
of clear or sun shade vi sor as sem blies.  The hel met is de signed to per mit the use of the
MBU-17/P ox y gen mask if re quired.

1-2  SCOPE

This man ual con tains a de scrip tion of the HGU-84/P  Com mer cial  Hel met  As sem bly 
as well as the siz ing, fit ting, and main te nance in struc tions re quired to out fit aircrew
mem bers suc cess fully and to main tain the equip ment prop erly.

1-3  SYS TEM 
DE SCRIP TION

1-3.1 HELMET AS SEM BLY

The air craft hel met 
as sem bly  is  avail able 
with one of the 
fol low ing  vi sor 
con fig u ra tions:  (1)  a  pair 
of light weight vi sors, 
(2) a sin gle vi sor 
as sem bly,  or 
(3) a dual vi sor as sem bly
with a quick-dis con nect 
for night vi sion goggles.  
These  con fig u ra tions 
are shown in Fig ure 
1-1.  A chin/nape 
strap as sem bly and a 
ther mo plas tic  liner 
as sem bly  are  added 
to the hel met shell 
as sem bly for a better 
fit and in creased 
sta bil ity.

1-1

Fig ure 1-1.  HGU-84/P  Com mer cial  Hel met  As sem bly

 

          HELMET WITH
SINGLE VISOR ASSEMBLY

             HELMET WITH 
     DUAL VISOR ASSEMBLY
       (QUICK DISCONNECT)

HELMET WITH LIGHTWEIGHT VISORS

Содержание HGU-84/P































































Отзывы: