Genie Z-51/30J Скачать руководство пользователя страница 89

Страница: 89 / 144

October 2020

Part No. 1268553GT

Z®-51/

31J

Service and Repair Manual

Deutz TD 2.2 L3 Engine Fault Codes

1165 5571

Rail fuel pressure relief valve
is forced to open. Warning
conditions.

1166 5571

Open rail fuel pressure relief valve
was detected.

1167 5571

Unexpected opening of the rail fuel
pressure relief valve.

1168 5571

Successful rail fuel pressure relief
valve opening cannot be ensured.

1169 5571

Averaged rail fuel pressure after
valve opening is outside the
expected tolerance range.

DTC

SPN

FMI Description

1170 5571

Open time of rail fuel pressure relief
valve for wear out monitoring had
exceeded.

1171 94

Fuel pressure build up during engine
start not successful.

1172 1347

Electrical fuel pump current below
normal or open circuit.

1174 1347

Electrical fuel pump voltage above
normal or shorted to high.

1175 1347

Electrical fuel pump voltage below
normal or shorted to low.

119

1231

CAN Bus 2 off Error for Application
CAN.

1190 7103

Rail fuel pressure below set
point, speed-dependent threshold
exceeded.

1191 7103

Rail fuel pressure metering unit. Fuel
quantity balance is disrupted.

1194 7103

Negative rail fuel pressure governor
deviation at zero delivery by
metering unit.

DTC = Diagnostic Trouble Code
FMI = Failure Mode Identifier
SPN = Suspect Parameter Number

1195 7103

Rail fuel pressure value is below
minimum rail pressure threshold.

1197 7103

Maximum rail fuel pressure
exceeded.

1198 7103

Set point of fuel metering unit in
overrun mode not plausible.

120

639

CAN Bus 1 off Error for Power train
CAN.

1200 5357

Shut-off due to undershoot of
minimum rail pressure.

1202 157

Maximum rail pressure exceeded in
limp home mode.

1208 157

Engine fuel injector metering rail
pressure voltage above normal or
shorted to high.

DTC

SPN

FMI Description

1209 157

Engine fuel injector metering rail
pressure voltage below normal or
shorted to low.

121

520252 2

Wrong checksum in the CAN
message EAT Control.

1212 629

ECU. Keep alive error during runtime
at an external device.

1213 629

ECU. Keep alive error during
initialization phase at an external
device.

1215 629

ECU. Read diagnosis error for non
volatile memory.

1216 629

ECU. Write diagnosis error for non
volatile memory.

1218 629

ECU. Stack memory threshold
overrun.

1219 629

ECU. Observation counter irregular
switch off counter triggered by
engine running.

122

4207

TSC1 message checksum fault.

123

4207

TSC1 message checksum fault.

1233 5826

Emission control system operator
inducement level 1 severity above
normal operational range.

Содержание Z-51/30J

















































































































































Результаты поиска

Содержание Z-51/30J

Отзывы:

Похожие инструкции для Z-51/30J

Бренды по названию

Популярные бренды

Genie Z-51/30J, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание Z-51/30J

Отзывы:

Похожие инструкции для Z-51/30J

Бренды по названию

Популярные бренды