Genie Z-51/30J Скачать руководство пользователя страница 65

Страница: 65 / 144

October 2020

Part No. 1268553GT

Z®-51/

31J

Service and Repair Manual

Manifolds

8-2

Valve Adjustments - Function

Manifold

How to Adjust the System

Relief Valve

Note: Perform this procedure with the boom in the
stowed position.

Note: Refer to Function Manifold Component list to
locate the system relief valve.

1 Connect a 0 to 5000 psi / 0 to 350 bar pressure

gauge to the test1 port on the function
manifold.

2 Start the engine from the ground controls.

3 Hold the function enable switch to the high

rpm position and activate and hold the primary
boom retract switch with the boom fully
retracted.

4 Observe the pressure reading on the pressure

gauge. Refer to Specifications,

Hydraulic

Specifications.

5 Turn the engine off. Use a wrench to hold the

relief valve and remove the cap.

6 Adjust the internal hex socket. Turn it clockwise

to increase the pressure or counterclockwise to
decrease the pressure. Install the relief valve
cap.

WARNING

Tip-over hazard. Do not adjust
the relief valve higher than
specified.

7 Repeat steps 2 through 5 and recheck relief

valve pressure.

8 Remove the pressure gauge.

How to Adjust the Secondary

Boom Down Relief Valve

Note: Perform this procedure with the boom in the
stowed position.

Note: Refer to Function Manifold Component list to
locate the secondary boom down relief valve.

1 Connect a 0 to 5000 psi / 0 to 350 bar pressure

gauge to the test1 port on the function
manifold.

2 Start the engine from the ground controls.

3 Hold the function enable switch to the high rpm

position and activate and hold the secondary
boom down switch with the secondary boom
fully lowered.

4 Observe the pressure reading on the pressure

gauge. Refer to Specifications,

Hydraulic

Specifications.

5 Turn the engine off. Use a wrench to hold the

relief valve and remove the cap.

6 Adjust the internal hex socket. Turn it clockwise

to increase the pressure or counterclockwise to
decrease the pressure. Install the relief valve
cap.

WARNING

Tip-over hazard. Do not adjust
the relief valve higher than
specified.

7 Repeat steps 2 through 5 and recheck relief

valve pressure.

8 Remove the pressure gauge.

Содержание Z-51/30J

















































































































































Результаты поиска

Содержание Z-51/30J

Отзывы:

Бренды по названию

Популярные бренды

Genie Z-51/30J, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание Z-51/30J

Отзывы:

Бренды по названию

Популярные бренды