manualshive.com logo in svg

Genie Z-51/30J, Руководство по обслуживанию и ремонту

Поделиться
Скачать
Genie Z-51/30J Скачать руководство пользователя страница 69

October 2020

Part No. 1268553GT 

Z®-51/

31J

 59 

Service and Repair Manual

How to Set Up the Directional 

Valve Linkage

Note: Adjustment of the oscillate directional valve 
linkage is only necessary when the linkage or 
valve has been replaced.

1  Lower the boom to the stowed position.

2  Use a "bubble type" level to be sure the floor is 

completely level.

WARNING

Tip-over hazard. Failure to 
perform this procedure on a 
level floor could compromise the 
stability of the machine resulting 
in the machine tipping over.

3  Check the tire pressure in all four tires and add 

air if needed to meet specification.

Note: The tires on some machines are foam-filled 
and do not need air added to them.

4  Remove the drive chassis cover and the non-

steer axle covers.

5  Place a "bubble type" level across the drive 

chassis non-steer end. Check to be sure the 
drive chassis is completely leve.

6  Remove the ball joint retaining fastener from 

the bracket.

7  To level the drive chassis, start the engine and 

push up or pull down on the threaded rod until 
the machine is completely level.

8  Verify that the ground and drive chassis are 

completely level.

Manifolds

9  Adjust the ball joint until the hole lines up with 

the retaining fastener hole in the bracket.

10 Install the ball joint to the axle and tighten the 

jam nut.

11 Check to be sure the drive chassis is 

completely level.

12 Measure the distance between the drive 

chassis and the non-steer axle on both sides 
(from the inside of the drive chassis).

Note: If the distance is not equal and the 
adjustment to the linkage was completed with the 
ground and drive chassis level, repeat steps 6 
through 11 OR consult Genie Product Support.

Содержание Z-51/30J

















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды