Genie Z-51/30J Скачать руководство пользователя страница 29

Страница: 29 / 144

October 2020

Part No. 1268553GT

Z®-51/

31J

Service and Repair Manual

Note: Do not operate any machine function during
the 10 second waiting time.SENSOR SETTINGS
is shown on the display.

Ramp rate (factory settings)
Primary boom up/down

accelerate
decelerate

4 seconds

0.5 second

Secondary boom up/down

accelerate
decelerate

2 seconds

0.5 second

Turntable rotate

accelerate
decelerate

2 seconds

0.5 second

Drive

accelerate
decelerate to neutral
decelerate, change of direction
decelerate, coasting
decelerate, braking
decelerate, shift from low
to high speed
decelerate, shift from high
to low speed

3 seconds

0.5 second

0.5 seconds

0.75 second

1 second

2 seconds

How to Adjust the Joystick

Threshold Setting

The threshold setting of a joystick is the minimum
output at which a function proportional valve can
open and allow the function to operate.

Note: Perform this procedure with the boom in the
stowed position.

1 Pull out the red Emergency Stop button to the

on position at both the ground and platform
controls.

2 Turn the key switch to platform control. Do not

start the engine.

3 Push in the platform controls red Emergency

Stop button to the off position.

4 Do not press down the foot switch.

5 Move and hold the drive enable toggle switch

in the right position and pull out the red
Emergency Stop button to the on position.

6 When the alarm sounds, release the drive

enable toggle switch.

7 Momentarily activate the drive enable toggle

switch in the right direction 8 times.

Result: There should be a pause and the
alarm should sound 8 times indicating that the
machine is in threshold calibration mode.

Result: The alarm does not sound. Repeat
steps 3 through 7.

8 Start the engine from the platform controls and

press down the foot switch.

Platform Controls

Содержание Z-51/30J

















































































































































Результаты поиска

Содержание Z-51/30J

Отзывы:

Бренды по названию

Популярные бренды

Genie Z-51/30J, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание Z-51/30J

Отзывы:

Бренды по названию

Популярные бренды