Genie Z-51/30J Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 144

background image

October 2020

Part No. 1268553GT

Z®-51/

31J

21

Service and Repair Manual

2-1 Platform Leveling Slave

Cylinder

The slave cylinder and the rotator pivot are the
two primary supports for the platform. The slave
cylinder keeps the platform level through the entire
range of boom motion. It operates in a closed-
circuit hydraulic loop with the master cylinder. The
slave cylinder is equipped with counterbalance
valves to prevent movement in the event of a
hydraulic line failure.

How to Remove the Platform

Leveling Slave Cylinder

Note: Before cylinder removal is considered, bleed
the slave cylinder to be sure there is no air in the
closed loop.

Note: When removing a hose assembly or fitting,
the O-ring (if equipped) on the fitting and/or hose
end must be replaced. All connections must be
torqued to specification during installation. Refer to
Specifications, H

ydraulic Hose and Fitting Torque

Specifications

.

1 Extend the primary boom until the slave

cylinder barrel-end pivot pin is accessible.

2 Raise the primary boom slightly and place

blocks under the platform for support.

3 Lower the primary boom until the platform is

resting on the blocks just enough to support the
platform.

Note: Do not rest the entire weight of the boom on
the blocks.

4 Tag, disconnect and plug the hydraulic hoses

from the slave cylinder at the unions and
connect them together using a connector.
Connect the hoses from the cylinder together
using a connector.

WARNING

Bodily injury hazard. Spraying
hydraulic oil can penetrate and
burn skin. Loosen hydraulic
connections very slowly to allow
the oil pressure to dissipate
gradually. Do not allow oil to
squirt or spray

.

5 Remove the pin retaining fastener from the

slave cylinder rod-end pivot pin. Do not remove
the pin.

6 Remove the external snap rings from the slave

cylinder barrel-end pivot pin. Do not remove the
pin.

7 Place a block under the slave cylinder for

support. Protect the cylinder rod from damage.

8 Use a soft metal drift to drive the rod-end pivot

pin out.

WARNING

Crushing hazard. The platform
could fall when the slave cylinder
rod-end pivot pin is removed if
not properly supported.

NOTICE

Component damage hazard.
The slave cylinder rod may
become damaged if it is allowed
to fall if not properly supported
by the lifting device.

9 Use a soft metal drift and drive the barrel-end

pin out.

10 Carefully pull the cylinder out of the primary

boom.

Platform Controls

«
...
29
30
31
32
33
...
»

Содержание Z-51/30J

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Z-51/30J

Genie GTH-4020 ER

Бренд: Terex Страницы: 188

Бренд: Terex Страницы: 80

Бренд: TIGIEFFE Страницы: 124

Бренд: Rotary Страницы: 27

Бренд: Rotary Страницы: 36

Бренд: Rotary Lift Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды