Genie Z-51/30J Скачать руководство пользователя страница 55

Страница: 55 / 144

October 2020

Part No. 1268553GT

Z®-51/

31J

Service and Repair Manual

Engines

6-1

RPM Adjustment

Refer to Maintenance Procedure in the appropriate
Maintenance Manual for your machine,

Check and

Adjust the Engine RPM

6-2 Flex Plate

The flex plate acts as a coupler between the
engine and the pump. It is bolted to the engine
flywheel and has a splined center to drive the
pump.

How to Remove the Flex Plate

1 Disconnect the battery cables from the battery

WARNING

Electrocution/burn hazard.
Contact with electrically charged
circuits could result in death or
serious injury. Remove all rings,
watches and other jewelry.

2 Disconnect the electrical connectors at the

electrical proportional controller, located on the
drive pump.

3 Support the drive pump with an appropriate

lifting device. Then remove all of the bell
housing to engine mounting bolts. Leave the
pump connected to the bell housing.

4 Carefully pull the pump and bell housing away

from the engine and secure it from moving.

NOTICE

Component damage hazard.
Hoses can be damaged if they
are kinked or pinched.

5 Remove the flex plate mounting fasteners, then

remove the flex plate from the engine flywheel.

Содержание Z-51/30J

















































































































































Результаты поиска

Содержание Z-51/30J

Отзывы:

Похожие инструкции для Z-51/30J

Бренды по названию

Популярные бренды

Genie Z-51/30J, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание Z-51/30J

Отзывы:

Похожие инструкции для Z-51/30J

Бренды по названию

Популярные бренды