Genie Z-51/30J Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 144

background image

vi Z®-51/

31J

Part No. 1268553GT

October 2020

Service and Repair Manual

Personal Safety

Any person working on or around a machine must
be aware of all known safety hazards. Personal
safety and the continued safe operation of the
machine should be your top priority.

Read each procedure thoroughly. This

manual and the decals on the machine,

use signal words to identify the following:

Safety alert symbol—used to alert

personnel to potential personal

injury hazards. Obey all safety

messages that follow this symbol

to avoid possible injury or death.

Indicates an imminently

hazardous situation which, if not

avoided, will result in death or

serious

injury.

Indicates a potentially hazardous

situation which, if not avoided,

could result in death or serious

injury.

Indicates a potentially hazardous

situation which, if not avoided,

may cause minor or moderate

injury.

Indicates a potentially hazardous

situation which, if not avoided,

may result in property damage.

Be sure to wear protective eye wear and

other protective clothing if the situation

warrants it.

Be aware of potential crushing hazards

such as moving parts, free swinging or

unsecured components when lifting or

placing loads. Always wear approved

steel-toed shoes.

DANGER

WARNING

CAUTION

NOTICE

Workplace Safety

Be sure to keep sparks, flames and

lighted tobacco away from flammable and

combustible materials like battery gases

and engine fuels. Always have an

approved fire extinguisher within easy

reach.

Be sure that all tools and working areas

are properly maintained and ready for

use. Keep work surfaces clean and free of

debris that could get into machine

components and cause damage.

Be sure any forklift, overhead crane or

other lifting or supporting device is fully

capable of supporting and stabilizing the

weight to be lifted. Use only chains or

straps that are in good condition and of

ample capacity.

Be sure that fasteners intended for one

time use (i.e., cotter pins and self-locking

nuts) are not reused. These components

may fail if they are used a second time.

Be sure to properly dispose of old oil or

other fluids. Use an approved container.

Please be environmentally safe.

Be sure that your workshop or work area

is properly ventilated and well lit.

SAFETY RULES

«
...
4
5
6
7
8
...
»

Содержание Z-51/30J

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Z-51/30J

Бренд: EAE Страницы: 42

Genie Z-34/22DC

Бренд: Terex Страницы: 56

Бренд: Terex Страницы: 71

Genie SX-105 XC

Бренд: Terex Страницы: 76

Бренд: HSS Hire Страницы: 10

Бренд: GMG Страницы: 31

Бренд: GMG Страницы: 34

Бренд: GMG Страницы: 37

Бренд: GMG Страницы: 68

Бренд: Atlas Страницы: 35

3219 SJIII Compact Series

Бренд: Skyjack Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды