manualshive.com logo in svg

Genie Z-51/30J, Руководство по обслуживанию и ремонту

Поделиться
Скачать
Genie Z-51/30J Скачать руководство пользователя страница 24

14 Z®-51/

31J

 

Part No. 1268553GT

October 2020

Service and Repair Manual

About This Section

Most of the procedures in this section should only 
be performed by a trained service professional 
in a suitably equipped workshop. Select the 
appropriate repair procedure after troubleshooting 
the problem.

Perform disassembly procedures to the point 
where repairs can be completed. Then to re-
assemble, perform the disassembly steps in 
reverse order.

Symbols Legend

Safety alert symbol—used to 
alert personnel to potential 
personal injury hazards. Obey all 
safety messages that follow this 
symbol to avoid possible injury or 
death.

DANGER

Indicates an imminently 
hazardous situation which, if not 
avoided, will result in death or 
serious injury.

WARNING

Indicates a potentially hazardous 
situation which, if not avoided, 
could result in death or serious 
injury.

CAUTION

Indicates a potentially hazardous 
situation which, if not avoided, 
may cause minor or moderate 
injury.

NOTICE

Indicates a potentially hazardous 
situation which, if not avoided, 
may result in property damage.

 

Indicates that a specific result is expected after 
performing a series of steps.

  Indicates that an incorrect result has occurred 

after performing a series of steps.

Repair Procedures

Содержание Z-51/30J

















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды