Genie Z-51/30J Скачать руководство пользователя страница 78

Страница: 78 / 144

68 Z®-51/

31J

Part No. 1268553GT

October 2020

Service and Repair Manual

Fault Codes

Before Troubleshooting:

Read, understand and obey the safety rules

and operating instructions in the appropriate
operator's manual on your machine.

Be sure that all necessary tools and test

equipment are available and ready for use.

Read each appropriate fault code thoroughly.

Attempting short cuts may produce hazardous
conditions.

Be aware of the following hazards and follow

generally accepted safe workshop practices.

WARNING

Electrocution/burn hazard.
Contact with electrically charged
circuits could result in death or
serious injury. Remove all rings,
watches and other jewelry.

Note: Two persons will be required to safely
perform some troubleshooting procedures.

Observe and Obey:

Troubleshooting and repair procedures shall be

completed by a person trained and qualified on
the repair of this machine.

Immediately tag and remove from service a

damaged or malfunctioning machine.

Repair any machine damage or malfunction

before operating the machine.

Unless otherwise specified, perform each

procedure with the machine in the following
configuration:

• Machine parked on a firm, level surface
• Key switch in the off position with the key

removed

• The red Emergency Stop button in the off

position at both the ground and platform

controls

• Wheels chocked
• All external AC power supply disconnected

from the machine

• Boom in the stowed position
• Turntable secured with the turntable rotation

lock

• Welder disconnected from the machine (if

equipped with the weld cable to platform
option)

Содержание Z-51/30J

















































































































































Результаты поиска

Содержание Z-51/30J

Отзывы:

Похожие инструкции для Z-51/30J

Бренды по названию

Популярные бренды

Genie Z-51/30J, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание Z-51/30J

Отзывы:

Похожие инструкции для Z-51/30J

Бренды по названию

Популярные бренды