Genie Z-51/30J Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 144

background image

44 Z®-51/

31J

Part No. 1268553GT

October 2020

Service and Repair Manual

Secondary Boom Components

3 Tag, disconnect and plug the hydraulic hoses

on the secondary boom lift cylinder.

WARNING

Bodily injury hazard. Spraying
hydraulic oil can penetrate and
burn skin. Loosen hydraulic
connections very slowly to allow
the oil pressure to dissipate
gradually. Do not allow oil to
squirt or spray.

4 Remove the pin retaining fasteners from the

secondary boom lift cylinder rod-end pivot pin
and barrel-end pivot pin. Do not remove the
pins.

5 Attach a strap from an overhead crane to the

lug on the rod end of the secondary boom lift
cylinder for support. Do not apply any lifting
pressure.

6 Use a soft metal drift to drive the barrel-end

pivot pin half way out. Lower the barrel end of
the secondary boom lift cylinder and let it hang
down.

7 Use a soft metal drift to drive the rod-end pivot

pin half way out.

8 Remove the secondary boom lift cylinder from

the machine.

WARNING

Crushing hazard. The secondary
boom lift cylinder could become
unbalanced and fall when
removed from the machine if
not properly attached to the
overhead crane.

NOTICE

Component damage hazard.
When removing a secondary
boom lift cylinder from the
machine, be careful not to
damage the counterbalance
valve at the barrel end of the
cylinder.

«
...
52
53
54
55
56
...
»

Содержание Z-51/30J

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Z-51/30J

Бренд: Bil-Jax Страницы: 13

Бренд: Manitou Страницы: 108

Бренд: Manitou Страницы: 138

Бренд: Manitou Страницы: 142

Бренд: Manitou Страницы: 160

Бренд: AMGO Страницы: 20

Бренд: nifty Страницы: 40

Бренд: nifty Страницы: 41

Heightrider HR15 HYBRID

Бренд: nifty Страницы: 42

HR17 HYBRID SERIES

Бренд: nifty Страницы: 45

TrackDrive TD120T Series

Бренд: nifty Страницы: 55

Бренд: Genie Страницы: 38

Бренд: Genie Страницы: 65

ZX-135/70 with Jib-Extend

Бренд: Genie Страницы: 82

Бренд: Genie Страницы: 185

Бренд: Genie Страницы: 205

Бренд: TEUPEN Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды