Genie Z-51/30J Скачать руководство пользователя страница 26

Страница: 26 / 144

16 Z®-51/

31J

Part No. 1268553GT

October 2020

Service and Repair Manual

Platform Controls

1-2

Joysticks

How to Calibrate a Joystick

The joysticks on this machine utilize digital Hall
Effect technology for proportional control. If a
joystick is disconnected or replaced, it must be
calibrated before that particular machine function
will operate.

Note: The joystick must be calibrated before the
threshold, max-out or ramp rate can be set.

Note: Perform this procedure with the engine off

1 Open the platform control box.

2 Pull out the red Emergency Stop button to the

on position at both the ground and platform
controls.

3 Turn the key switch to platform control. Do not

start the engine.

4 Select a joystick to calibrate.

5 Disconnect the wire harness connector from

the joystick for approximately 10 seconds
or until the alarm sounds. Connect the wire
harness connector to the joystick.

6 Move the joystick full stroke in either direction

and hold for 5 seconds.

7 Return the joystick to the neutral position,

pause for a moment, then move the joystick
full stroke in the opposite direction. Hold for 5
seconds and return the joystick to the neutral
position.

Result: The alarm should sound indicating
successful joystick calibration.

8 Repeat this procedure for each joystick

controlled machine function including the thumb
rocker steer switch..

Note: No machine function should operate while
performing the joystick calibration procedure.

Содержание Z-51/30J

















































































































































Результаты поиска

Содержание Z-51/30J

Отзывы:

Похожие инструкции для Z-51/30J

Бренды по названию

Популярные бренды

Genie Z-51/30J, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание Z-51/30J

Отзывы:

Похожие инструкции для Z-51/30J

Бренды по названию

Популярные бренды