General Equipment RIP-R-STRIPPER FCS16 Скачать руководство пользователя страница 34

Страница: 34 / 63

FCS16 RIP-R-STRIPPER

FORM GOM4240301, VERSION 3.1

BLADE CONTROL SYSTEM

Misaligned jackscrew bearing. Loosen and realign.

Improper

lubrication.

See

LUBRICATION

REQUIREMENTS.

Bent jackscrew. Replace jackscrew and flexible joint

assembly.

UNEVEN COVERING MATERIAL REMOVAL

Excessive material build-up on caster wheel face

surface. Remove material. Readjust wheel scraper to

wheel gap setting: .03/.06 inch (.8/1.5 mm).

Excessive caster wheel bearing wear. Replace caster

wheel and shoulder type cap screw.

Excessive axle shoulder type cap screw wear. Replace

cap screw. Check caster wheel bearing for wear.

Replace as necessary.

Damaged elastomeric rubber mount(s). Replace

mount(s).

Damaged exciter plate. Replace plate.

Bent blade. Replace blade.

Storage

Proper procedure for long term storage of the RIP-R-

STRIPPER will protect it against the effects of

corrosion and damage. If the RIP-R-STRIPPER is not

to be operated for a period of 30 days or more,

proceed to store as follows:

1) Never store the RIP-R-STRIPPER with the blade or

ceramic tile ripper attachment installed. Remove the

blade or ceramic tile ripper attachment from the RIP-R-

STRIPPER per the procedures outlined in this manual.

Do not store the RIP-R-STRIPPER with the

blade or ceramic tile ripper attachment

attached. This configuration can result in

property damage and/or personal injury.

2) Clean all accumulated foreign material from the RIP-

R-STRIPPER utilizing an appropriate safety solvent.

Observe all applicable safety precautions for

the solvent.

3) Check all visible parts for wear, breakage or damage.

Order any part required to make the necessary repair.

This will avoid a needless delay when operating the

RIP-R-STRIPPER at next use.

4) Apply a dry film lubricant to all exposed metal

components to prevent rust.

5) Block the bottom of the main frame to prevent

machine weight against the exciter plate. This

procedure will reduce impact loads to the elastomeric

rubber mounts, minimize deflection and increase

service life.

6) Store the RIP-R-STRIPPER inside. If the RIP-R-

STRIPPER must be stored outside, protect it with a

suitable covering.

Specifications

FRAME

STRUCTURE

Unitized, welded steel plate.

DRIVE SYSTEM Random orbit, direct shaft

mount.

NUMBER OF ELASTOMERIC RUBBER MOUNTS

WIDTH

14-1/2 inches (368 mm).

WIDTH (AT OPERATOR HANDLE)

23 inches

(584 mm).

LENGTH (HANDLE FOLDED) 24 inches (610 mm).

LENGTH (OPERATING CONFIGURATION) 34 inches

(864 mm).

HEIGHT (HANDLE FOLDED)

23 inches (584 mm).

HEIGHT (MAXIMUM HANDLE EXTENSION)

inches (1067 mm).

GENERAL

WEIGHT (WITH EXTERNAL WEIGHT

130 lbs

LESS BLADE)

(59 kg).

Содержание RIP-R-STRIPPER FCS16
































































Результаты поиска

Содержание RIP-R-STRIPPER FCS16

Отзывы:

Бренды по названию

Популярные бренды

General Equipment RIP-R-STRIPPER FCS16, Руководство оператора

Результаты поиска

Содержание RIP-R-STRIPPER FCS16

Отзывы:

Бренды по названию

Популярные бренды