General Equipment RIP-R-STRIPPER FCS16, Руководство оператора

Страница: 28 / 63

FCS16 RIP-R-STRIPPER
FORM GOM4240301, VERSION 3.1
26
5) The coverings removal process on many work
surface materials can produce sparks, dust and other
foreign particle contamination. Many covering
materials, adhesives and/or mastics can contain
asbestos and other chemicals that are known to cause
physical harm and/or affect the environment. These
types of materials need to be properly identified,
contained and disposed of according to established
OSHA, EPA and other rules and regulations.
SPARKS PRODUCED BY THE ACTIONS OF
BLADE AND/OR CERAMIC TILE RIPPER
AT TA C H M E N T A G A I N S T T H E W O R K
S U R FA C E ( F O R E X A M P L E : S T R I K I N G
ANCHOR BOLTS) CAN RESULT IN A FIRE
AND/OR EXPLOSION. THIS OCCURRENCE
C A N R E S U LT I N P R O P E R T Y D A M A G E
AND/OR PERSONAL INJURY.
THE CREATION OF DUST AND OTHER
F O R E I G N PA R T I C L E C O N TA M I N AT I O N
FROM THE COVERING REMOVAL PROCESS
CAN RESULT IN PROPERTY DAMAGE
AND/OR PERSONAL INJURY. FOR SUCH
OPERATING CONDITIONS, ALWAYS WEAR
A N I O S H / M S H A A P P R O V E D D U S T / M I S T
RESPIRATOR AND APPROPRIATE SAFETY
R E L A T E D A P P A R E L . C O N S U L T
APPLICABLE OSHA REGULATIONS FOR
SPECIFIC INFORMATION.
6) Dust and other particle contamination can be
controlled by the use of an appropriate industrial type
vacuum system to remove/control dust and other
particle contamination from the work surface.
ALWAYS UTILIZE A VACUUM SYSTEM TO
OPERATE WITHIN THE SPECIFIC JOB SITE
R E Q U I R E M E N T. D U S T M AT E R I A L C A N
M E E T C L A S S I I O R C L A S S I I I
S P E C I F I C AT I O N S O F T H E N AT I O N A L
ELECTRIC CODE ® FOR HAZARDOUS
L O C A T I O N C L A S S I F I C A T I O N S .
CONSIDERATION MUST ALSO BE GIVEN TO
THE CREATION OF HAZARDOUS TYPE
M AT E R I A L S R E Q U I R I N G S P E C I F I C
D I S P O S A L P R O C E D U R E S . D E T E R M I N E
THAT THE VACUUM SYSTEM IS PROPERLY
DESIGNED TO OPERATE WITHIN THESE
AT M O S P H E R E S . C O N S U LT C U R R E N T
NATIONAL ELECTRIC CODE®, OSHA AND
ENVIRONMENTAL PROTECTION AGENCY
R E G U L A T I O N S F O R S P E C I F I C
INFORMATION.
7) Water applied to the work surface is not normally
utilized to control dust and other particle
contamination. Water, and/or other conductive
materials, should be removed from the work surface by
an industry approved and/or accepted practice
BEFORE utilizing the RIP-R-STRIPPER to remove the
covering material. The presence of water and/or any
other conductive material on the work surface can
substantially increase the potential electrocution
concern for the operator and/or associated work
personnel.
WATER OR OTHER CONDUCTIVE
MATERIALS DEPOSITED ON THE WORK
S U R F A C E I N C R E A S E S T H E
ELECTROCUTION POTENTIAL FOR THE
OPERATOR AND/OR ASSOCIATED WORK
P E R S O N N E L . D E T E R M I N E T H E R I P - R -
STRIPPER IS PROPERLY GROUNDED (NO
FAULTS), THE EXTENSION CORD IS FREE
OF CUTS, ABRASIONS, EXPOSED CABLE
STRANDS AND THAT THE GFI PROPERLY
F U N C T I O N S T O E L I M I N A T E F A U L T
C O N C E R N S . I M P R O P E R M A C H I N E
GROUNDING, EXTENSION CORDS AND/OR
GFI CAN RESULT IN PROPERTY DAMAGE
AND/OR PERSONAL INJURY.
8) Normal usage of the RIP-R-STRIPPER will allow the
build-up and accumulation of work surface materials on
the surfaces. It is highly recommended that both the
interior and exterior surfaces be properly cleaned after
the completion of each use.
Failure to properly clean the interior surfaces
of the RIP-R-STRIPPER can result in dried